unstable TL-SG2428P v1.0

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

unstable TL-SG2428P v1.0

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
unstable TL-SG2428P v1.0
unstable TL-SG2428P v1.0
2023-07-04 14:51:08 - last edited 2023-11-05 08:24:56
Model: TL-SG2428P  
Hardware Version: V1
Firmware Version: 1.1.7 Build 20221222 Rel.51105

Hello friends

 

I think the switch is broked and has to be exchanged.

 

A customer has

 

- OC200 as Omada Controller

- ER605 v2.0 as Router (connected over PPPOE to internet)

- TL-SG2428P v1.0 as Switch

- 2x EAP225 as Accesspoints

 

Problem:

 

After hours of working, suddenly OC200, Accesspoints/WiFi and VOIP DECT POE station are not reachable anymore.

Internet over cable is stil working, but thats the only thing working then.

 

After removing powercord, everything is working again.

Everyday, customer have to "fix" this, but it is not the solution.

 

Seems to me to be a bad switch, since everything connected to the switch is "dead"...

Strange thing is, that internet is stil working, so computer, that are connected over cable, can just work, but no phone, no wifi and no connection to OC200...

 

Some ideas?

 

Thanks

  0      
  0      
#1
Options
1 Accepted Solution
Re:unstable TL-SG2428P v1.0-Solution
2023-11-05 08:22:45 - last edited 2023-11-05 08:24:56

  @Jayjay28 

Hi,

after some research with supportteam, I had to replace this switch via RMA. There was no other solution. Since replacement, everything works like a charm.

Recommended Solution
  0  
  0  
#4
Options
3 Reply
Re:unstable TL-SG2428P v1.0
2023-07-05 02:13:03

  @kogan 

have you verified the local IP address on devices on this switch? how do you determine it's a bad switch? 

verify the cables? the config? anything messed up by your customer? any loop? checked the log? Link  LED on the switch on or off? 

 

if you have not done these yet, I don't think the community can help. this is basic troubleshooting to locate and isolate the problem.

ScReW yOu gUyS. I aM GOinG hoMe. —————————————————————— For heaven's sake, can you write and describe your issue based on plain fact, common logic and a methodologic approach? Appreciate it.
  0  
  0  
#2
Options
Re:unstable TL-SG2428P v1.0
2023-11-05 08:20:24

  @kogan Do you found a solution for the issue? I have a similar problem with a customer. The switch runs stable for 2-3 weeks and then I have the same error pattern as described above. I installed the latest firmware TL-SG2428P(UN)_V5_5.0.5 Build 20230602 3 weeks ago. Unfortunately, this has not changed anything either.

 

Have you been able to solve the problem in the meantime?

  0  
  0  
#3
Options
Re:unstable TL-SG2428P v1.0-Solution
2023-11-05 08:22:45 - last edited 2023-11-05 08:24:56

  @Jayjay28 

Hi,

after some research with supportteam, I had to replace this switch via RMA. There was no other solution. Since replacement, everything works like a charm.

Recommended Solution
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 670

Replies: 3

Related Articles