Home

Forums

Stories

Knowledge Base

Home Network Community > DSL Modem Routers > VR600 Address Reservation Issue

< DSL Modem Routers

VR600 Address Reservation Issue

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

VR600 Address Reservation Issue

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

ESPMaker

2019-01-23 20:24:21 - last edited 2019-12-09 08:01:55

Posts: 2

Helpful: 1

Solutions: 0

Stories: 0

Registered: 2019-01-22

VR600 Address Reservation Issue

2019-01-23 20:24:21 - last edited 2019-12-09 08:01:55

Hello,

To describe the context... I am the "happy" owner of a VR600 router since a few month. Happy because of the great improvement in management compare to my ancient material. And between quotes "" because the capacities of the router management has recently reach their limits.

I think that I encounter the same problem that the one described here, were I have written a message :

https://community.tp-link.com/en/home/forum/topic/99457?page=1

But I finally decide to start a new thread about VR600 for the visibility.

Identifications:

The Firmware Version is: 0.2.0 0.9.1 v0074.0 Build 170504 Rel.68210n

The Hardware Version :Archer VR600 v2 00000000

The problem :

I have successfully entered 12 devices for address reservation, and then I have had the grey box blocking everything. I cannot define more reserved address. I tried to delete one entry to replace it with a new one : impossible. Delete operation was ok, but I have now only 11 reserved addresses and it's impossible to enter a new one. Modify existing entry doesn't work neither.

I have a complete IoT network to design. A large number of entries in the address reservation table is a mandatory for my project. Actually, this VR600 is only good for trash in my case, unless guarantee could play.

Will a corrected firmware be available soon ? At least, is an ancient firmware usable to avoid this serious bug ?

Best regards,

EM.

5 Reply

Kadi

LV1

2019-02-07 13:36:40 - last edited 2019-12-09 08:01:55

Posts: 2

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2019-02-07

Re:VR600 Address Reservation Issue

2019-02-07 13:36:40 - last edited 2019-12-09 08:01:55

Hi, I have the same issue, did you find a solution? thanks.

liutas4x4

LV1

2019-02-13 16:12:35 - last edited 2019-12-09 08:01:55

Posts: 4

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2019-02-13

Re:VR600 Address Reservation Issue

2019-02-13 16:12:35 - last edited 2019-12-09 08:01:55

Exactly the same error.

As I found at this desk, issue exits from 2017, and no one from TP-Link is on duty for it.

Hey, TP-Link, it is impossible to do a business with such kind of support today. You will ruin your image quckly, you see.

I bought the router more than 3 months ago, and I can not replace it.

Is anyone @ charge there?

Yours,
Eugenijus

Trappist

LV1

2019-12-07 16:08:43 - last edited 2019-12-09 08:01:55

Posts: 2

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2019-12-07

Re:VR600 Address Reservation Issue

2019-12-07 16:08:43 - last edited 2019-12-09 08:01:55

I have the same issue - has anyone found a solution to this problem yet?

@ESPMaker

Kevin_Z

2019-12-09 08:01:05 - last edited 2019-12-09 08:01:55

Posts: 21611

Helpful: 5056

Solutions: 2549

Stories: 21

Registered: 2018-12-24

Re:VR600 Address Reservation Issue

2019-12-09 08:01:05 - last edited 2019-12-09 08:01:55

@Trappist

What is the hardware and firmware version of the Archer VR600?

How many entries you can enable?

Any error message pops up when you failed to add more?

Good day.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

Trappist

LV1

2019-12-10 00:24:29

Posts: 2

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2019-12-07

Re:VR600 Address Reservation Issue

2019-12-10 00:24:29

@Kevin_Z

The firmware is: Version 0.2.0 0.9.1 v0074.0 Build 170504 Rel.68210n

The hardware is: Version Archer VR600 v2 00000000

When I purchased the router about two or three years ago I successfully entered 13 IP addresses into Address Reservation, but within the last six months I have tried on a number of occasions to add further IP addresses and have not succeeded.

I go to the Network -> LAN Settings page on the 'Advanced' tab in the web interface and can see the existing IP addresses listed in the Address Reservation table. If I click on 'Add' the IP address and MAC address data entry boxes momentarily appear on the screen (< 1 second) and then disappear and are replaced by a greyed-out block which allows no further interaction on the page. At this point the interface has frozen and can only be restored by switching back to the 'Basic' tab. All attempts to return to the Address Reservation feature and add new addresses end in failure in this way. The are no error messages as such - just a grey area blocking input to the screen.

I'd be very grateful for any further help you may be able to provide.

VR600 Address Reservation Issue

VR600 Address Reservation Issue

Information

Voters 1

Tags