Deco M4 in DMZ of modem/router - firewall?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Deco M4 in DMZ of modem/router - firewall?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Deco M4 in DMZ of modem/router - firewall?
Deco M4 in DMZ of modem/router - firewall?
2019-04-10 07:02:09
Model: Deco M4  
Hardware Version:
Firmware Version:

Hi,

(apologies if this is answered elsewhere - I haven't found what I needed searching the forums)

 

my setup  is   modem/router -> Main Deco M4 -> switch -> XBOX, PC, NAS, Other Deco M4s

 

Currently I have my main M4 as an access point - but would like to use it in router mode.

However, when I enabled this, I was getting a Double NAT warning on my XBOX (which I think might impact online gaming)

 

My modem/router doesn't have a bridge mode - so the only solution I can think of is putting the M4 in the DMZ of the modem/router.

 

My question is - are there security risks because of this? Does the M4 have any firewall?

(my main concern is the NAS on the M4 network, since I like having this behind a firewall from the internet at large)

 

My networking knowledge is pretty basic - so I might be overlooking something simple here..

 

thanks for any feedback/suggestions!

  0      
  0      
#1
Options
3 Reply
Re:Deco M4 in DMZ of modem/router - firewall?
2019-04-11 01:56:49

Hi,

 

FYI, the Deco M4 does not support DMZ yet, while it supports port forwarding. Regarding to the double NAT issue, you can setup the port forwarding for the Xbox.

 

M4 does have firewall, and cause the M4 connected to the modem/router, with double NAT existed, it will protect the whole network. 

 

May it help, good day.

jabberwookie wrote

Hi,

my setup  is   modem/router -> Main Deco M4 -> switch -> XBOX, PC, NAS, Other Deco M4s

 

Currently I have my main M4 as an access point - but would like to use it in router mode.

However, when I enabled this, I was getting a Double NAT warning on my XBOX (which I think might impact online gaming)

 

My modem/router doesn't have a bridge mode - so the only solution I can think of is putting the M4 in the DMZ of the modem/router.

 

My question is - are there security risks because of this? Does the M4 have any firewall?

(my main concern is the NAS on the M4 network, since I like having this behind a firewall from the internet at large)

 

My networking knowledge is pretty basic - so I might be overlooking something simple here..

 

thanks for any feedback/suggestions!

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  1  
  1  
#2
Options
Re:Deco M4 in DMZ of modem/router - firewall?
2019-11-29 12:36:18

@Kevin_Z 

 

Hi, 

 

I have very similar situation, so I want to ask from here instead of opening a new topic.

 

I have same configuration but instead of XBOX, I have a NAS that I want to reach from internet. 

 

I used to do port forwarding on my modem when I have only a modem but with additon of DECO, I have double NAT and I don't know how to do port forwarding in this situation.

 

What might be the convenient solution to do port forwarding now? 

 

PS: I was also planning to do DMZ from my modem but since now I learned that M4 do not support DMZ, I need to find another solution.

  0  
  0  
#3
Options
Re:Deco M4 in DMZ of modem/router - firewall?
2019-11-30 17:40:44

@aytek 

 

you'll have a double NAT issue if you don't put your existing router into a bridge mode and use your existing router purely as a modem and not a router. Then when your existing router is in bridge mode the WAN connection terminates on the Deco using something such as PPPoE (this depends on what your ISP says to do).

 

if you want to keep your existing router as a router then you will need to use the Decos in access point mode.

  1  
  1  
#4
Options