Remote management

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Remote management

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Remote management
Remote management
2019-04-23 11:17:36
Model: TD-W8961N  
Hardware Version: V3
Firmware Version: 180118

Hello

 

I am trying to remotely manage an adsl router.

I am using the adsl router TD-W8961N in bridge mode and assigning a different ip than the default (192.168.1.1) to 192.168.200.10.

I added in the access list a rule to allow all from wan also.

I have network (192.168.200.0/24) to the lan part behind the DSL modem and can access any computer in this range but can't access the ip on the interface LAN on the router itself.

 

Any help please.

Thanks.

  0      
  0      
#1
Options
7 Reply
Re:Remote management
2019-04-24 06:07:51

Hi,

 

What is the current network topology? 

 

FYI, in bridge mode, there is no IP address and other advanced features, it is used to sync the DSL connection only.

 

Please tell us the current operation mode of the router and the current internet IP address. 

Note: If it is a private IP address, you cannot access it remotely unless you opened the port for on the front-end device. 

 

May it help and have a nice day. 

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:Re:Remote management
2019-04-24 11:01:18

the current network topology is:

DSLAM connected to adsl router. the dsl router is in bridge mode then all newtwork behind dsl mode should be layer 2 network right.

I have pc connected to the dsl router whic is pingable and this pc can access the ip interface of the router and can manage it(192.168.200.10). The pc has IP 192.168.200.11.

I have another pc connected to the data (LAN) port of dslam through switch and can ping to the pc (192.168.200.11) behind the dsl bridge modem but can't ping the ip 192.168.200.10.

 

Thanks

  0  
  0  
#3
Options
Re:Re:Re:Remote management
2019-04-25 07:28:45

Hi,

 

If the DSL router works in bridge mode, do you have any other router?

 

Is it your network topology-- Dslam--8961n(brigde mode)--host router?If not, please correct me.

 

Please login to the web interface of the 8961N and show me a screenshot of the status page. 

Note: How to login: https://www.tp-link.com/en/support/faq/114/

 

Thanks in advance, and have a nice day. 

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#4
Options
Re:Re:Re:Re:Remote management
2019-04-25 09:53:24

 

I changed the ip to 192.200.200.177 I have PC connected to LAN port of the dsl with IP 192.200.200.178 which I can reach to it from anywhere in my network but I can't neither ping or access the LAN IP (192.200.200.177) of the ADSL modem.

I have other brands ADSL modems with same bridge mode and I can access the LAN ip of the modem.

  0  
  0  
#5
Options
Re:Re:Re:Re:Re:Remote management
2019-04-25 11:30:48

Hi,

 

As you know, the 8961N works as a bridge mode and the WAN IP shows N/A; so it cannot be access remotely.

 

For the computer connected to it, cause the current DHCP server is disabled, the computer cannot obtain an IP address from the 8961N, that is why you cannot ping it.

 

Considering you changed its LAN IP to 192.200.200.177, you can setup a static IP for your computer, IP is 192.200.200.x, x cannot be 177; after that, you can try to ping the DSL modem and test whether it works.

 

Note: How to setup static IP address: https://www.tp-link.com/en/support/faq/14/

 

May it help and have a nice day. 

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#6
Options
Re:Re:Re:Re:Re:Re:Remote management
2019-05-09 12:15:56

I have no problem with the computer connected to the dsl modem it is working and I already assigned a static IP on it.

The problem is that I can't access the LAN IP of the dsl Modem from any other side on the layer 2 network. I can access it only from the LAN side where the computer is assigned the static ip. But I want to access it from the dslam network or from another dsl bridge modem. I have other dsl modems and are configured as bridge also but I can access the firewall and allow to accept icmp and web protocol to the dsl modem from the wan side (through the dsl).

  0  
  0  
#7
Options
Re:Re:Re:Re:Re:Re:Re:Remote management
2019-05-10 11:12:59

Hi,

 

From the picture, the modem router works as a bridge mode, so that you cannot use the remote management. 

 

You setup static IP for your computer  to access internet, it has nothing to do with the 8961N.

 

When it works as a bridge, it is just used to sync the DSL connection and connect your computer to it by wired cable to get internet with static IP.

 

May it help and have a nice day. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#8
Options