Home Network Community > DSL Modem Routers > Can't enable guest network / Can't save wireless settings.
< DSL Modem Routers

Can't enable guest network / Can't save wireless settings.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Can't enable guest network / Can't save wireless settings.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Can't enable guest network / Can't save wireless settings.
Can't enable guest network / Can't save wireless settings.
2019-06-16 15:46:03 - last edited 2019-06-17 06:45:59
Model: TD-W8961N  
Hardware Version:
Firmware Version: Build 150630 Rel.34713

So hello everyone.

Got an issue with my rooter :

 

I can't enable Guest Network, everytime i hit "enable" it refreshes the page and put it to the original state (disabled) and i can't change any option of it.

Can't change also Wireless Settings, i can have acces to those options, change them but when i hit "save" nothing happens, and when i refresh the page, there's no option changing too.

 

Thanks for your incoming help.

 

(PS : I don't know where do i get to know my hardware version)

  0      
 
  0      
 
#1
Options
7 Reply
Re:Can't enable guest network / Can't save wireless settings.
2019-06-16 17:04:36 - last edited 2019-06-17 06:45:59
The version number should be on the tag on your router. As far as your guest network goes, be sure to page down to the bottom of the screen and click "save".
  0  
  0  
#2
Options
Re:Can't enable guest network / Can't save wireless settings.
2019-06-17 06:45:50 - last edited 2019-06-17 06:45:59

Hi,

 

Try to change another web browser or another device to access the web interface.

 

After you changed the wireless settings or enable guest network, please click save and test whether it works.

 

Besides, you can refer to instruction below to get the hardware version: 

https://www.tp-link.com/support/faq/46/

 

May it help and have a nice day. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#3
Options
Re:Can't enable guest network / Can't save wireless settings.
2019-10-05 20:55:05
Same to me, other device: can't save settings.
  0  
  0  
#4
Options
Re:Can't enable guest network / Can't save wireless settings.
2019-10-11 07:08:03

@Dietmar 

 

Have you ever tried the suggestions mentioned on my last reply? 

 

Besides, please ensure that your device has connected to the TP-Link router before you enabled the guest network and save it. 

 

Best regards. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#5
Options
Re:Can't enable guest network / Can't save wireless settings.
2019-10-11 13:34:56

@Kevin_Z 

Thanks. Yes, as in my other post (https://community.tp-link.com/en/home/forum/topic/172602) I've tried four browsers on three devices with three operating systems. The SAVE button just does exactly -nothing- in each respective combination.

  0  
  0  
#6
Options
Re:Can't enable guest network / Can't save wireless settings.
2019-10-11 15:37:02

@Dietmar Have you tried a reset to factory? I know that is not fun as you need to re-enter all of the router settings but it may help you in this case.

  0  
  0  
#7
Options
Re:Can't enable guest network / Can't save wireless settings.
2019-10-12 01:48:19

@Dietmar 

 

Thanks for your reply, that is a little weird, as Archer C8 said, you can hard reset the router and verify whether it works after that. 

 

Best regards. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#8
Options

Information

Helpful: 0

Views: 2235

Replies: 7

Related Articles
Can't save hue settings
4153 1
 can't enable wireless 2.4ghz / wireless disabled
5493 1
 Can't Connect To Any Wireless Network
2693 0
 I can't enable 1.0gbps
548 0
Can't find how to enable the n WiFi mode in TLWN881ND
2919 0
 AX6000 can't restrict guest network bandwith?
423 1
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.