Home Network Community > Deco > [SOLVED] Deco M5 port forwarding -- not working
< Deco

[SOLVED] Deco M5 port forwarding -- not working

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

[SOLVED] Deco M5 port forwarding -- not working

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
[SOLVED] Deco M5 port forwarding -- not working
[SOLVED] Deco M5 port forwarding -- not working
2019-08-26 13:44:59 - last edited 2022-05-11 07:51:38
Model: Deco M5  
Hardware Version:
Firmware Version: 1.3.1 Build 20190617 Rel. 47476

I've been trying to set up port forwarding on my M5's to pass traffic on port 51413 to my laptop, but I just can't get it to work.

 

I have three Deco M5 units using wireless backhaul. The master unit is connected by ethernet to my ISP's Huawei modem/router, which is in Bridged mode. I've set the Deco's DHCP server to use 192.168.0.* rather than the default 192.168.68.*, just because I prefer it. (But port forwarding didn't work before i made this change, either.)

 

All firewall, DMZ and port forwarding settings on the Huawei unit are disabled, and the malicious content filter and intrusion prevention on the Deco are enabled. Apart from port forwarding, everything about the network is functioning as expected.

 

The local address of the laptop I'm forwarding to is 192.168.0.100, so the port forwarding entry in the Deco app looks like this:

 

 

Locally, I can telnet to the required port:

 

 

However, in the app I'm running on the laptop, and on any other port scanning software I've tried, the port is still closed when accessed from my public IP:

 

 

What should I check next to proceed?

 

UX Designer, Software Developer, Scottish bloke.
  0      
 
  0      
 
#1
Options
2 Accepted Solutions
Re:Deco M5 port forwarding -- not working-Solution
2019-08-28 00:16:14 - last edited 2019-08-28 00:16:22

I've now solved this -- dumb user error, as usual.

 

I'd bridged the wrong connection on my ISP's router, so I had a double NAT situation. Having fixed that, port forwarding is now working as expected.

UX Designer, Software Developer, Scottish bloke.
Recommended Solution
  0  
  0  
#6
Options
Re:[SOLVED] Deco M5 port forwarding -- not working-Solution
2022-05-11 07:51:19 - last edited 2022-05-11 07:51:25

Hi All,

For the port forwarding issue on Deco, please refer to this link:

 Cannot open ports on Deco/port forwarding is not working

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶Deco X50-5G-V1-1.2.0 Supports WireGuard VPN, Hybrid Mesh and More Try to leave a Message if urgent help is required.
Recommended Solution
  0  
  0  
#10
Options
9 Reply
Re:Deco M5 port forwarding -- not working
2019-08-27 01:31:25

@calum-b 

 

Hello, what is the current internet IP address? 

 

Please use the computer in the same network to do the tests below and tell us the results.

 

A. Use LAN IP+port to test if the service can be accessed from LAN;

B. Use WAN IP+port on LAN PC to test if the port is opened.

 

Meanwhile, please disable the firewall and anti-virus software on the computer. 

 

Any updates, just let us know. 

 

Good day. 

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:Deco M5 port forwarding -- not working
2019-08-27 01:35:46

I recommend you try connecting to the service from another device on your local LAN as a validation test - you can telent to the port from the machine itself, but it is quite possible that firewall rules or filtering on the machine are blocking connections from outside the device.

  0  
  0  
#3
Options
Re:Re:Deco M5 port forwarding -- not working
2019-08-27 11:27:06

ajharvey wrote

I recommend you try connecting to the service from another device on your local LAN as a validation test - you can telent to the port from the machine itself, but it is quite possible that firewall rules or filtering on the machine are blocking connections from outside the device.

 

Yes, good point. I have since tested that and the other machines on my LAN also see the port as open.

 

UX Designer, Software Developer, Scottish bloke.
  0  
  0  
#4
Options
Re:Re:Deco M5 port forwarding -- not working
2019-08-27 11:37:53 - last edited 2019-08-27 11:42:53

Kevin_Z wrote

@calum-b 

 

Hello, what is the current internet IP address? 

 

Please use the computer in the same network to do the tests below and tell us the results.

 

A. Use LAN IP+port to test if the service can be accessed from LAN;

B. Use WAN IP+port on LAN PC to test if the port is opened.

 

Meanwhile, please disable the firewall and anti-virus software on the computer.  

 

Thanks. I will PM you the current public IP address, but I don't have a static IP from my ISP so it will change from time to time.

 

For the test results below, I disabled the Sophos anti-virus (required for work) on the target laptop. The macOS firewall was already disabled, and I have no 3rd-party firewall software installed.

 

A: Using netcat to scan the LAN IP+port from another PC on my LAN, the port is open:

 

B: Using WAN IP+port from another PC on my LAN, the port is closed.

UX Designer, Software Developer, Scottish bloke.
  0  
  0  
#5
Options
Re:Deco M5 port forwarding -- not working-Solution
2019-08-28 00:16:14 - last edited 2019-08-28 00:16:22

I've now solved this -- dumb user error, as usual.

 

I'd bridged the wrong connection on my ISP's router, so I had a double NAT situation. Having fixed that, port forwarding is now working as expected.

UX Designer, Software Developer, Scottish bloke.
Recommended Solution
  0  
  0  
#6
Options
Re:Re:Deco M5 port forwarding -- not working
2019-08-28 01:11:21

@calum-b 

 

Hello, Calum, thanks  for your valued reply, glad to hear that you figured it out. Congrats. 

 

If need any further help, do not hesitate to contact us. 

 

Have a nice day. 

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#7
Options
Re:[SOLVED] Deco M5 port forwarding -- not working
2020-06-28 18:17:46

@calum-b how did you resolve the Double Nat issue?

  0  
  0  
#8
Options
Re:[SOLVED] Deco M5 port forwarding -- not working
2020-06-29 23:11:51 - last edited 2020-06-29 23:15:17

 

Bales1181 wrote

@calum-b how did you resolve the Double Nat issue?

@Bales1181 It was best part of a year ago now so I can't remember exactly what I originally did wrong I'm afraid... I just recall that I bridged the wrong connection intially. (My ISP's router is a Huawei 658c, so there were four connections to choose from, as seen here: https://www.rgb.ie/2014/10/29/enable-bridge-mode-in-vodafone-hg658c-router/#post/0).

UX Designer, Software Developer, Scottish bloke.
  0  
  0  
#9
Options
Re:[SOLVED] Deco M5 port forwarding -- not working-Solution
2022-05-11 07:51:19 - last edited 2022-05-11 07:51:25

Hi All,

For the port forwarding issue on Deco, please refer to this link:

 Cannot open ports on Deco/port forwarding is not working

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶Deco X50-5G-V1-1.2.0 Supports WireGuard VPN, Hybrid Mesh and More Try to leave a Message if urgent help is required.
Recommended Solution
  0  
  0  
#10
Options

Information

Helpful: 0

Views: 16549

Replies: 9

Related Articles
 Deco M5 Port Forwarding - NOT WORKING
3116 0
Port forwarding [SOLVED]
1006 0
Deco M5 Port Forwarding not working? (Setting up a Java Minecraft Server)
6429 0
Deco M5 - Port Forwarding - device connected but not listed
879 2
 [Solved] Port forwarding not working
1850 0
 Deco M5 port forwarding to a wired device NOT working
1144 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.