Archer MR600(EU) V1 - BETA Firmware - Allowing selection of 4G+bands for Archer MR600 manually
Hi all,
Following the long thread on the same subject discssing the BETA FW, as I said I would, TPLink have given me permission to share the FW download llink.
From TPLink - We recently released a beta firmware for Archer MR600(EU) V1 which can allow us to select 4G+bands for Archer MR600 manually.
https://static.tp-link.com/2020/202004/20200420/Archer_MR600v1_1.1.0_0.9.1_[200417-rel75138]_up_boot_2020-04-20_08.44.31.zip
For Archer MR600, if you want to use its 4G+network, your SIM card should support the CA bands group Archer MR400 supports. Please check the attached picture and check if your SIM card supports the band groups on the list or not.
They asked me to state that, this BETA FW is for the Archer MR600(EU) V1 ONLY!
Neither TPLink nor me take any respnsbility if you flash a none-EU router.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi recently i bought tplink mr600 v1 and was curious to update it to beta firmware....can u tell me which is the latest beta firmware to flash..which allows to select band for CA( carrier aggregation).
- Copy Link
- Report Inappropriate Content
Hi, you can get the latest beta firmware here:
- Copy Link
- Report Inappropriate Content
No proper solution for v1 at all.. very bad with TPLINK after paying much for this router.. and now I have almost 6 TPLINK routers and suggested the same my friends circle, now ended with unsatisfactory form them as well as they depend on my guidance. and its time change to other brand or alternate method.
- Copy Link
- Report Inappropriate Content
@Satheskumar Merry Christmas to TP link Forum.Its been a quite long time since I am out of these pages. I have taken a wise decision after I disposed of the box MR600.I am quite impressed with the Huawei B525s-65a LTE router. It's delivering constant speeds and locking the bands together effectively. I am using it with Airtel on CA_40A-40A. Peak hours and off hours LTE speeds are amazing. Have flashed it with a custom Firmware to lock the PCI/ CellID which is really beneficial in getting the best signal from my nearest tower. details below. The results are with external cross polarized panel Antenna.
Satheskumar wrote
No proper solution for v1 at all.. very bad with TPLINK after paying much for this router.. and now I have almost 6 TPLINK routers and suggested the same my friends circle, now ended with unsatisfactory form them as well as they depend on my guidance. and its time change to other brand or alternate method.
- Copy Link
- Report Inappropriate Content
This is the last version working for me:
1.1.0 0.9.1 v0001.0 Build 200417 Rel.75138
I uninstalled the December version because the router frequently didn't start well.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Yes even i have faced the same issue today.. I thought proplem with laptop wifi the I noticed other devices also not able to connect with tplink router, i did reset router to solve problem.. hope we get some fix pack from tplink shortly.
sassi wrote
yes all says that have probleme in reboot not boot corectly
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Hi all,
as first thanks for accepting me in this community.
I've just bought a brand new MR600, and I'd like to test the beta FW. Can I roll back to the original FW in case of problem ?
Thanks in advance and happy new year !
Have a good day,
Felice
- Copy Link
- Report Inappropriate Content
hi nice post i am also fedup with mr600 kindly provide link to buy Huawei B525s-65a and also provide link for custom firemware
- Copy Link
- Report Inappropriate Content
Information
Helpful: 13
Views: 192641
Replies: 511