Troubleshooting LED loop on Deco/ Deco stuck in solid yellow
This Article Applies to:
All Deco models
Typical Problem Description:
1. One of the Deco units was stuck in constant yellow light mode and was not able to enter setup mode (blue blinking light);
2. One of the Deco units goes into this reboot loop of Solid Yellow > Blinking Yellow > Blinking Blue > Off > Solid Yellow, this cycle keeps on repeating.
If Deco had a solid or flashing red, please have a look at this link: Deco turned red
Troubleshooting suggestions:
1. Please hold the reset pinhole at the bottom of the Deco for 1s and check whether the light could be back to yellow---flashing blue.
2. If the factory reset did not make any difference, please refer to this link to do a firmware recovery:
https://www.tp-link.com/support/faq/2958/
If the issue continues, please comment below with the following information:
1. The model number as well as the firmware version of the Deco;
2. Which problem description is more like your current issue?
3. Have you tried the hardware reset and firmware recovery suggestions? what are the results?
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
1. The model number as well as the firmware version of the Deco;
Model: DECO E4R
SN: 2224547B02454
2. Which problem description is more like your current issue?
One of the 2 DECO´s that I have has the "stuck in solid yellow"
3. Have you tried the hardware reset and firmware recovery suggestions? what are the results?
Yes, it is still stuck in solid yellow
- Copy Link
- Report Inappropriate Content
Hi, welcome to the community.
How long have you had the Deco E4?
I am afraid the hardware might be broken and if it is within warranty, you could contact the local shop retailer to get it replaced first.
Thank you very much.
Best regards.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@TP-Link My Deco XE75 V2 is looping between solid yellow -> blinking blue -> solid blue -> yellow. I can not add it to my network. The deco seems un responsive.
Please help
- Copy Link
- Report Inappropriate Content
I have just purchased 3 Deco XE75 Pro.
1. The model number as well as the firmware version of the Deco;
Model: DECO XE75 Pro
SN: 222B4R9B00039
2. Which problem description is more like your current issue?
Two of the 3 DECO´s that I have has the "stuck in solid yellow"
3. Have you tried the hardware reset and firmware recovery suggestions? what are the results?
Yes, I have try the reset and the firmware recovery with both methods and they are still stuck in solid yellow.
- The http method never connect.
- The ftp method does 2 blue -blink then goes to solid green with nothing on the ftp log activity. unplugging the device after goes back to stuck in yellow.
Can you help me please @TP-Link ?
- Copy Link
- Report Inappropriate Content
Model Number: Deco M5 Version 3.6.27
The lisght stays only in Solid Yellow even after rebooting through the app and the hard reset button.
I do not know how to do the firmware reset.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@TP-Link My Deco x55 is stuck on yellow and the firmware recovery failed. S/N Y225058B00559
- Copy Link
- Report Inappropriate Content
@TP-Link trust is no.1
now not recomended for me
- Copy Link
- Report Inappropriate Content
@TP-Link same issue in my M4 Deco, solid yellow light. I tryed the firmware reset and did not worked.
The Message was: updated file failed.
Any other suggestion?
- Copy Link
- Report Inappropriate Content
Information
Helpful: 2
Views: 48423
Replies: 51
Voters 0
No one has voted for it yet.