Range Extenders Support OneMesh/EasyMesh in AP Mode
Hey everyone!
We got some feedback from our community users requesting for Range Extender to support OneMesh/EasyMesh when works as an Access Point.
Currently, OneMesh/EasyMesh is not supported when the extender is set to Access Point Mode. However it is planned to support EasyMesh over Ethernet Backhaul under Range Extender mode.
It will start with RE315_V1 and gradually be added to other EasyMesh-supported extenders.
EasyMesh Range Extenders Start Supporting Building a EasyMesh Network via Ethernet Backhaul
Note:
1. An extender needs to support EasyMesh (over Wi-Fi) first, then supports EasyMesh over Ethernet Backhaul.
2. Ethernet Backhaul only works when both your main router and satellite extender support EasyMesh over Ethernet Backhaul.
Other Mesh Options:
Option 1: Deco mesh system supports Ethernet backhaul under both Wireless Router and Access Point modes.
Deco Ethernet Backhaul feature and Topology
Kindly note that the Deco system is different from TP-Link OneMesh >>> TP-Link OneMeshâ„¢ VS Deco Mesh: What's the Difference?
Option 2: OneMesh---Compatible Powerline devices if your house is under the same power circuit/under the same power meter
Some powerline products could build OneMesh through Ethernet & house Power line
Powerline units that supports OneMesh
How to configure OneMesh with seamless roaming (Powerline Extender)
Related Articles:
Several questions about the OneMeshâ„¢ and Mesh
How to build an Ethernet Backhaul using TP-Link EasyMesh Range Extenders
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
You can return it....
This request is the most wated request since 2020 . and after they promise to development this feature we are waiting for it and until now we didn't see any progress .
- Copy Link
- Report Inappropriate Content
@Riley_S just wanted to bring this post to your attention since I know it has been mentioned in other channels
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
It is one thing that my products (AX80 and a few RE330) cannot connect over the Ethernet, but if they are connected, one cannot even enter router admin page. One may say, "Obviously!", however other products - even within the TP-Link family - use of Ethernet backhaul.
- Copy Link
- Report Inappropriate Content
Disappointed. Bought 2 days ago 1 AX55 and 2 RE200(AR) for the onemesh feature. And after googling how to set it up with ethernet found this thread.
3 years passed since this feature was requested and no firmware update to support it.
- Copy Link
- Report Inappropriate Content
@tryqwe Hi, welcome to the community. If you just purchased Archer AX55+RE200, I think you might consider replacing it with Deco whole Mesh system. It has good compatibility with Ethernet Backhaul.
https://www.tp-link.com/en/home-networking/deco/
General questions about Ethernet Backhaul feature on your Deco
Thank you very much.
Best regards.
- Copy Link
- Report Inappropriate Content
The Deco ethernet backhaul is not what we as your consumers are looking for - it works on a different sub-net than the internet router, and requires a separate network and additional TP-Link switch to establish the ethernet backhaul.
- Copy Link
- Report Inappropriate Content
Could you please update us on this feature status?
Replacing our current devices with the "Deco" line-up is not an option and not the answer that we, your customers, are looking for.
Regards,
Ernestas
- Copy Link
- Report Inappropriate Content
@David-TP I need the USB 3.0 port. I don't want to spend another couple a 100$ for two Deco when you can update the firmware to make it work. If ichange it will be certainly not with Tp-link.
- Copy Link
- Report Inappropriate Content
@Solla-topee @David-TP do we have any updates on this initiative - 2 years is MUCH too long for such a simple firmware update to be developed
- Copy Link
- Report Inappropriate Content
Information
Helpful: 169
Views: 84315
Replies: 246
Voters 142
