Forums

Stories

Knowledge Base

Home Network Community > Deco > Deco P9 PLC issue

< Deco

Deco P9 PLC issue

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Deco P9 PLC issue

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Deco P9 PLC issue

DanishS

LV1

2021-12-17 16:29:25 - last edited 2022-07-14 02:24:30

Posts: 2

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2021-12-06

Deco P9 PLC issue

2021-12-17 16:29:25 - last edited 2022-07-14 02:24:30

Model: Deco P9

Hardware Version: V2

Firmware Version: 1.1.3 Build 20201228 Rel. 55057

Model: Deco P9 (2.0)

Hardware Version: V2

Firmware Version: 1.1.3 Build 20201228 Rel. 55057

Hi,

I have an issue with my P9. At the main deco I get about 460-480 on a speed test, I have a 500 Mbps line. One of the secondary units shows a PLC connection as well as wifi, but the speed is miserable, at just 20 Mbps. I dont think the PLC is working as it is just holding on to the wifi.

The 3rd unit is worse and just shows only a wifi connection about 95% of the time. I see a PLC connection maybe twice a week. Max speed I have seen is 2Mbps. This deco shows a connection from the secondary unit, so speed has degraded considerably.

Any solution for this?

Have seen other posts of the P9 issue for the version 1 which was sorted with a beta version of the firmware.

Thank you in advance.

1 Accepted Solution

TP-Link

2021-12-21 08:00:17 - last edited 2022-07-14 02:25:24

Posts: 6834

Helpful: 2495

Solutions: 534

Stories: 28

Registered: 2018-07-23

[Solution]Deco P9 PLC issue-Solution

2021-12-21 08:00:17 - last edited 2022-07-14 02:25:24

Update:

Occasionally, There is some feedback that PLC backhaul on the Deco P9 is unstable, most of the time satellite units are on wireless backhaul only and had a slow speed.

Here we have provided the following beta firmware for your reference:

Deco P9-V2-1.1.2 build 20210113

(It could be reverted back to official firmware later)

Note: Be sure you have read the Terms and Conditions for TP-Link Beta Firmware before proceeding!

Please comment below and keep me informed whether the beta firmware is working or not.

Thank you very much.

Best regards.

Deco Monthly Recap- Check What's Currently Going on With Deco

Recommended Solution

-MMK-

LV1

2022-02-19 19:53:00

Posts: 3

Helpful: 3

Solutions: 0

Stories: 0

Registered: 2022-02-19

Re:Deco P9 PLC issue

2022-02-19 19:53:00

I have sama problem. 3rd deco lost plc connection. Model: Deco P9 Hardware Version: V2 Firmware Version: 1.1.3 Build 20201228 Rel. 55057 Model: Deco P9 (2.0) Hardware Version: V2 Firmware Version: 1.1.3 Build 20201228 Rel. 55057 Any solution for this ?

-MMK-

LV1

2022-02-21 13:04:47

Posts: 3

Helpful: 3

Solutions: 0

Stories: 0

Registered: 2022-02-19

Re:Deco P9 PLC issue

2022-02-21 13:04:47

@TP-Link I have sama problem. 3rd deco lost plc connection. Model: Deco P9 Hardware Version: V2 Firmware Version: 1.1.3 Build 20201228 Rel. 55057 Model: Deco P9 (2.0) Hardware Version: V2 Firmware Version: 1.1.3 Build 20201228 Rel. 55057 Any solution for this ?

Can i test test "beta" firmware?

TP-Link

2022-02-22 05:50:43

Posts: 6834

Helpful: 2495

Solutions: 534

Stories: 28

Registered: 2018-07-23

Re:Deco P9 PLC issue

2022-02-22 05:50:43

@-MMK-

Hi, please refer to the private message to get the beta firmware.

At the same time, can I have more details about the current issue:

1. would any P9 turn red during the disconnection?

2. Could you please switch the location of the 3^rd P9 with the 2^nd to see whether the unstable PLC connection follows with a specific location or a specific node？

Deco Monthly Recap- Check What's Currently Going on With Deco

MikkiH

LV1

2022-06-23 18:59:57

Posts: 1

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2022-06-23

Re:Deco P9 PLC issue

2022-06-23 18:59:57

@TP-Link Can I have the beta software too?

DPW239

LV1

2022-07-13 10:59:55

Posts: 1

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2022-07-13

Re:Deco P9 PLC issue

2022-07-13 10:59:55

@TP-Link Hi,

I've been having the same problem, one unit in particular doesn't seem to want to connect. I'm using the same hardware/firmware on all of my units as described by the OP.

Could I get the beta firmware too, please?

Thanks.

TP-Link

2022-07-14 02:26:40

Posts: 6834

Helpful: 2495

Solutions: 534

Stories: 28

Registered: 2018-07-23

Re:Deco P9 PLC issue

2022-07-14 02:26:40

@DPW239 MikkiH

Please refer to the "Recommended Solution" to test the beta firmware.

And please let me know whether it is working or not.

Best regards.

Deco Monthly Recap- Check What's Currently Going on With Deco

David-TP

2022-10-21 02:20:26

Posts: 9992

Helpful: 1310

Solutions: 851

Stories: 9

Registered: 2020-04-14

Re:Deco P9 PLC issue

2022-10-21 02:20:26

@MikkiH Hi， Thanks for your message. I did not log into the @TP-Link account so maybe it could be better for me to reply here.

I see you have three Deco P9 and did both satellite units behave quite the same: Satelite deco lost plc and never again connect plc?

The powerline backhaul highly relies on the current electric environment and if possible, please try to move it far away from the home appliances.

And would there be any chance to connect P9 via Ethernet cables?

I noticed you mentioned the beta firmware worked for some days. Did it stop working again recently?

Thank you very much.

Best regards.

Deco Monthly Recap- Check What's Currently Going on With Deco KidShield Test Recruitment, Share Your Ideas With us!

DanishS

LV1

2021-12-17 16:29:25 - last edited 2022-07-14 02:24:30

Posts: 2

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2021-12-06

Information

Helpful: 0

Replies: 8

Deco P9 PLC issue

Deco P9 PLC issue

Information

Voters 0

Tags