Official Release Deco M9 Plus 1.6.4
Current Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.4_Build_20240718
Release Note:
1. Improve the device stability;
2. Enhance the system security
---------------------------------------------------------------------------------------------------
History Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.3_Build_20231225
Release Note:
1. Fix the potential security vulnerability and its related problem.
2. Improve system stability and security.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.2_Build_20230906
Release Note:
1.Fixed the bug that parental control doesn't take effect.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.1_Build 20230403
Release Note:
1. Added Reboot Schedule for every day/week under Deco App > More > Reboot Schedule.
2. Added support for customizing Satellite Deco Signal Source under Deco App > Internet > Select the Satellite Deco > Signal Source.
3. Added support for customizing clients Connection Preference under Deco App > CLIENTS > Select the client > Click the gear icon on the right-up corner > Connection Preference.
4. Added No-IP and DynDNS to the DDNS settings under Deco App > More > Advanced > DDNS.
5. Added Smart DHCP on/off switch in Access Point mode under Deco App > More > Advanced > Smart DHCP.
6. Added a prompt notification when the Ethernet link rate goes down to 100Mbps.
7. Added schedule and bandwidth limit to guest network under Deco App > More > Wi-Fi > Guest Network.
8. Fixed the bug that the built-in speedtest has low speed test results.
Notes:
1. This firmware downgrade could be done via firmware recovery-How to use firmware recovery.
2. Please update your Deco APP to the latest version for the new features.
3. If there are non-1.6.0 models in the Mesh network, you may miss some new features but this feature will be supported via firmware update in the future.
4. You may miss some new features when Deco is set to Access Point mode.
Related Articles:
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
@David-TP
I have tested like you asked and nothing changed. I have sent an email with the requested information
- Copy Link
- Report Inappropriate Content
@David-TP After updating my M9 Plus V2.0 to this firmware when i jump between deco access points by physically moving between AP's or by changing the preferred connection/access point all packets are dropped for minutes or until I disconnect/connect wifi. I'm testing using ping to local gateway and internet.
However the WIFI does appear to remain connected.
This didn't happen on previous firmware. Enabling/disabling fast roaming, beam forming or "mesh technology" on the device does not affect the behavior.
I can replicate this issue consistently. Has this been reported by anyone else?
My topology is as follows:
AP1 (main connected to internet) --- AP2 (Connected to WIFI) --- AP3 (Connected with cable to AP1).
1. I start a ping request on my iPhone to 1.1.1.1 while connected to AP3.
2. Walk to AP2 one packet is dropped during handover.
3. Walk to AP1 one packet is dropped during handover.
4. Walk back to AP2
5. Walk back to AP3 (starting point) all packets dropped until WIFI-reconnection or several minutes waited.
I noticed the following warnings in the log following new steer event for my MAC-address.
Thu May 25 12:01:44 2023 user.err csrMeshGw[6341]: MSGQ :: CsrMeshAddMsgToTxQueue idx: 0x0, Msg Len: 30, Repeat: 2
Thu May 25 12:01:44 2023 user.err csrMeshGw[6341]: MSGQ :: CsrMeshGetMsgFromTxQueue curTxIndex : 0, tag count : 2, length : 30
Thu May 25 12:01:44 2023 user.err csrMeshGw[6341]: MSGQ :: CsrMeshGetMsgFromTxQueue curTxIndex : 0, tag count : 1, length : 30
Thu May 25 12:01:44 2023 user.err csrMeshGw[6341]:
CsrMeshMsgQRead: qId=0 errno=42, No message of desired type!!!!
FYI: I have also submitted a ticket to technical support.
- Copy Link
- Report Inappropriate Content
@David-TP I have 3 in the m9 plus and all configured as Ac. no1 connects to no2 by cable and no3 connects to no2 by wi-fi. all version 2 with firmware 1.6.1. every day I have to restart the nodes because they lose performance during the day and usually at night the speed is terrible and it is necessary to restart to get back to normal.
I don't know how to get log of ac to put it here.
Thanks
- Copy Link
- Report Inappropriate Content
Hello,
Since the upgrade, I've got wifi issues. Here is my Setup
Main: Deco M9 v2 with 1.6.1 build 20230403 rel 70058 (access point mode)
Satellites: several Deco M9 v1/v2 and M5
Since the firmware upgrade, I had:
- wifi connection issues (password refused)
- wifi stability issues (performance A/O timeouts)
- no issue when connected to the main Deco or a satellite with an ethernet cable
I already recreated the network from scratch twice and problems still occur
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Thanks for info! /jannek999
- Copy Link
- Report Inappropriate Content
Hi, Thank you for the feedback.
As for the disconnection issue, could you please refer to this link to help me check which case is quite like yours? I think it might be the third one and if yes, you could refer to the suggestions of turning off fast roaming and beamforming here to see whether it helped.
Fix unstable connection when connected to the Deco network
As for the speed issue, can I have more details about it?
May I know how many online clients you have?
Wait for your reply.
Best regards.
- Copy Link
- Report Inappropriate Content
Hi, welcome to the community.
Could you please send me some pictures of the network map and the signal strength on the Decos, such as:
It is also suggested to refer to the following advice:(case 3)
Fix unstable connection when connected to the Deco network
May I know the model number of the clients that dropped out frequently?
Wait for your reply.
Best regards.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Information
Helpful: 10
Views: 112245
Replies: 440
Voters 2
