Official Release Deco M9 Plus 1.6.4
Current Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.4_Build_20240718
Release Note:
1. Improve the device stability;
2. Enhance the system security
---------------------------------------------------------------------------------------------------
History Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.3_Build_20231225
Release Note:
1. Fix the potential security vulnerability and its related problem.
2. Improve system stability and security.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.2_Build_20230906
Release Note:
1.Fixed the bug that parental control doesn't take effect.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.1_Build 20230403
Release Note:
1. Added Reboot Schedule for every day/week under Deco App > More > Reboot Schedule.
2. Added support for customizing Satellite Deco Signal Source under Deco App > Internet > Select the Satellite Deco > Signal Source.
3. Added support for customizing clients Connection Preference under Deco App > CLIENTS > Select the client > Click the gear icon on the right-up corner > Connection Preference.
4. Added No-IP and DynDNS to the DDNS settings under Deco App > More > Advanced > DDNS.
5. Added Smart DHCP on/off switch in Access Point mode under Deco App > More > Advanced > Smart DHCP.
6. Added a prompt notification when the Ethernet link rate goes down to 100Mbps.
7. Added schedule and bandwidth limit to guest network under Deco App > More > Wi-Fi > Guest Network.
8. Fixed the bug that the built-in speedtest has low speed test results.
Notes:
1. This firmware downgrade could be done via firmware recovery-How to use firmware recovery.
2. Please update your Deco APP to the latest version for the new features.
3. If there are non-1.6.0 models in the Mesh network, you may miss some new features but this feature will be supported via firmware update in the future.
4. You may miss some new features when Deco is set to Access Point mode.
Related Articles:
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Dear David, it seems that the frequent disconnects and reconnects are not yet fixed in this August 23 version. I have a few devices which I have set an alert when they go online and offline. What could be the reason for this? I haven't done this offline/online notificafions for all my devices. It seems that this is a stability issue which everyone has been pointing out. I have attach above my screenshot of my notifications.
- Copy Link
- Report Inappropriate Content
I was able to install it. I just had to quit the initiated process after waiting for almost an hour and redo the firmware upgrade. Thank you David. I appreciate your hardwork on this.
- Copy Link
- Report Inappropriate Content
Thanks for the feedback.
I tested on my side and the firmware upgrade works quite normal.
It is suggested to update Deco one by one, starting from the satellite M9 first. An Ethernet connection is highly recommended.
Wait for your reply.
Best regards.
- Copy Link
- Report Inappropriate Content
I am upgrading to the latest update using For V2/2.2/2.6/2.8, Download link: Deco_M9_V2_1.6.0_220823
How long does this take? I started the upgrade but it keeps spinning and it says uploading. I have been waiting for about 15 minutes now since i hit upgrade. I don't see any progress bar.
- Copy Link
- Report Inappropriate Content
Thank you! After about 30mins I was able to get the tool to work and the V2.8 hardware was updated successfully. I am able to see the IP addresses of both devices and I am able to set which Deco they should connect to.
- Copy Link
- Report Inappropriate Content
Hi, I see the V2 of your Deco M9 plus is on 1.2.12 and it might need to be updated to 1.6.0 via firmware upgrade utility:
Thank you very much.
- Copy Link
- Report Inappropriate Content
I decided to wait a few weeks until i updated to the beta just to make sure there werent any major bugs. Updated today and only one of the 4 updated via the web tool, but i was able to update the rest using the downloadable update tool. I did have to reset my zigbee smart devices and rescan, but they finally reconnected to the decos also. selecting signal source of mesh units is working as expected. so far so good. thank you tplink devs for adding the m9+ 1.6 beta
- Copy Link
- Report Inappropriate Content
I guess something must be different here because when I go to the IP addresses of what I suspect the new v2.8 Decos are I get a message from them saying
Not Found
The requested URL /webpages/login.html was not found on this server.
The IPs don't show up in my app for those new Decos either, just the MAC addresses.
- Copy Link
- Report Inappropriate Content
@imakeholesinu you can go directly to each deco IP where you will find a web interface that allows you individual updates. I have at home 3 M9Plus Deco, two 2.0 and one 1.0 (meaning different firmware to apply) and that way worked fine. I hope that helps.
- Copy Link
- Report Inappropriate Content
Is there a procedure to follow to update a Deco network with different hardware versions? I have 3 v1 M9 Decos that I've updated to the beta firmware and now I'd like to update my 2 v2.8 M9 Decos.
Do I need to remove the v2.8's from my network, build a stand-alone network with just the v2.8s, update the firmware and then add them back to my main network?
- Copy Link
- Report Inappropriate Content
Information
Helpful: 8
Views: 142083
Replies: 436
Voters 2
