Official Release Deco M9 Plus 1.6.4
Current Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.4_Build_20240718
Release Note:
1. Improve the device stability;
2. Enhance the system security
---------------------------------------------------------------------------------------------------
History Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.3_Build_20231225
Release Note:
1. Fix the potential security vulnerability and its related problem.
2. Improve system stability and security.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.2_Build_20230906
Release Note:
1.Fixed the bug that parental control doesn't take effect.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.1_Build 20230403
Release Note:
1. Added Reboot Schedule for every day/week under Deco App > More > Reboot Schedule.
2. Added support for customizing Satellite Deco Signal Source under Deco App > Internet > Select the Satellite Deco > Signal Source.
3. Added support for customizing clients Connection Preference under Deco App > CLIENTS > Select the client > Click the gear icon on the right-up corner > Connection Preference.
4. Added No-IP and DynDNS to the DDNS settings under Deco App > More > Advanced > DDNS.
5. Added Smart DHCP on/off switch in Access Point mode under Deco App > More > Advanced > Smart DHCP.
6. Added a prompt notification when the Ethernet link rate goes down to 100Mbps.
7. Added schedule and bandwidth limit to guest network under Deco App > More > Wi-Fi > Guest Network.
8. Fixed the bug that the built-in speedtest has low speed test results.
Notes:
1. This firmware downgrade could be done via firmware recovery-How to use firmware recovery.
2. Please update your Deco APP to the latest version for the new features.
3. If there are non-1.6.0 models in the Mesh network, you may miss some new features but this feature will be supported via firmware update in the future.
4. You may miss some new features when Deco is set to Access Point mode.
Related Articles:
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Thank you very much for the confirmation.
The beta firmware is NOT suitable for V1/1.1/1.2. Sorry about the previous information and the original post has been updated.
Hi, It could be downgraded back to 1.5.6 if needed via firmware recovery. since it is much more complicated than the usual firmware upgrade and we also want to get more feedback about the beta firmware preparing for the official release of 1.6.0, it is not recommended to update to downgrade back to 1.5.6 at the first time.
Hi, I will test on my side to see whether it would be the same.
So far, have you noticed any abnormal issues with the Wi-Fi performance?
Thank you very much.
Best regards.
- Copy Link
- Report Inappropriate Content
@MorrisAGE No it only upgraded my V2 - @tp-link wheres the V1 file please?
- Copy Link
- Report Inappropriate Content
@internet4me " All working as expected."
That must be a relief. What are you supposed to do if it doesn't work and (as the readme says) you can't go back to 1.5.6?
- Copy Link
- Report Inappropriate Content
Hi!
I see the .bin file is named as M9Plus_2.0_en_1.6.0 Build 20220720 Rel. 62024_US_JP_EU_TW_CA_up.
Looks like it is only for V2.0 and upwards. I have a mix of V1 and V2 on the same mesh. Does this file upgrade V1 decos too?
- Copy Link
- Report Inappropriate Content
Installed firmware1.6.0. On m9 plus v2. All working as expected.
Except 1 thing. On the webpage of the mainrouter; The status for all WiFi information is blank. Lucky WiFi is working as expected. (No quest WiFi enabled)
- Copy Link
- Report Inappropriate Content
Information
Helpful: 8
Views: 142088
Replies: 436
Voters 2
