Official Release Deco M9 Plus 1.6.4
Current Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.4_Build_20240718
Release Note:
1. Improve the device stability;
2. Enhance the system security
---------------------------------------------------------------------------------------------------
History Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.3_Build_20231225
Release Note:
1. Fix the potential security vulnerability and its related problem.
2. Improve system stability and security.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.2_Build_20230906
Release Note:
1.Fixed the bug that parental control doesn't take effect.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.1_Build 20230403
Release Note:
1. Added Reboot Schedule for every day/week under Deco App > More > Reboot Schedule.
2. Added support for customizing Satellite Deco Signal Source under Deco App > Internet > Select the Satellite Deco > Signal Source.
3. Added support for customizing clients Connection Preference under Deco App > CLIENTS > Select the client > Click the gear icon on the right-up corner > Connection Preference.
4. Added No-IP and DynDNS to the DDNS settings under Deco App > More > Advanced > DDNS.
5. Added Smart DHCP on/off switch in Access Point mode under Deco App > More > Advanced > Smart DHCP.
6. Added a prompt notification when the Ethernet link rate goes down to 100Mbps.
7. Added schedule and bandwidth limit to guest network under Deco App > More > Wi-Fi > Guest Network.
8. Fixed the bug that the built-in speedtest has low speed test results.
Notes:
1. This firmware downgrade could be done via firmware recovery-How to use firmware recovery.
2. Please update your Deco APP to the latest version for the new features.
3. If there are non-1.6.0 models in the Mesh network, you may miss some new features but this feature will be supported via firmware update in the future.
4. You may miss some new features when Deco is set to Access Point mode.
Related Articles:
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Found an interesting issue.
All wireless devices seems connect to maindeco only. No wirelessdevices connect to other slavedecos. (Total 3x m9+)
Setting preferred deco for wireless device works.
both for 2.4 and 5ghz bands.
- Copy Link
- Report Inappropriate Content
Connectiom preferences seems stable. I noticed a few number of client disconnects then reconnects whenever deco app is opened and refreshed.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
I find the reconnects somewhat severe eventhough deco app is closed. I have a notification on a few clients when they turn online so I know once they reconnect. Can other beta testers confirm?
- Copy Link
- Report Inappropriate Content
@David-TP Is there any Deco M9 Plus trial firmware 1.6 available for hardware version 1?
- Copy Link
- Report Inappropriate Content
@David-TP will there be a release for v1.1 m9's? Why does this model lag behind?
- Copy Link
- Report Inappropriate Content
@Sofa_king_lazy DiceKey Lexivienna
Thank you very much for your time and patience.
There hasn't been any updated news about other models/versions yet.
If there is, I will update it here at once.
During this time, you are free to start a new thread about your current issue with Deco that might be related to the missing features.
Thanks a lot for your understanding and support.
Best regards.
- Copy Link
- Report Inappropriate Content
I’m just wondering at what point will the fixes that have gone into the M5 1.6.0 release will be merged into this beta build? I’m reluctant to apply this beta version knowing fixes from a previous beta haven’t been merged in.
- Copy Link
- Report Inappropriate Content
@David-TP I have three M9 Plus units at home, one 1.0 and two 2.0. Since the web tool only allows to select by model but not by version, I cannot see the way to apply this firmware update selectively - knowing that does not support 1.0, unless you confirm the web tool will not apply to those units incompatible with the firmware. Is that the case ?
In the other hand, I did not choose which firmware version I was getting when I bought my M9 Plus units. Therefore, please give ALL versions the same priority.
- Copy Link
- Report Inappropriate Content
Hi @aspaviento Mjather and All,
The 1.6.0 firmware for V1 has been uploaded as well and the previous fixes of issues reported on the 1.6.0 of Deco M5 also have been merged into the latest 1.6.0 build20220810 version.
Please reach out to the first post to install the beta firmware.
Thank you very much.
Best regards.
PS: Currently we also have 1.6.0 beta for Deco X55 V1 and if you are interested, please leave me a message.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 10
Views: 113017
Replies: 440