Official Release Deco M9 Plus 1.6.4
Current Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.4_Build_20240718
Release Note:
1. Improve the device stability;
2. Enhance the system security
---------------------------------------------------------------------------------------------------
History Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.3_Build_20231225
Release Note:
1. Fix the potential security vulnerability and its related problem.
2. Improve system stability and security.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.2_Build_20230906
Release Note:
1.Fixed the bug that parental control doesn't take effect.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.1_Build 20230403
Release Note:
1. Added Reboot Schedule for every day/week under Deco App > More > Reboot Schedule.
2. Added support for customizing Satellite Deco Signal Source under Deco App > Internet > Select the Satellite Deco > Signal Source.
3. Added support for customizing clients Connection Preference under Deco App > CLIENTS > Select the client > Click the gear icon on the right-up corner > Connection Preference.
4. Added No-IP and DynDNS to the DDNS settings under Deco App > More > Advanced > DDNS.
5. Added Smart DHCP on/off switch in Access Point mode under Deco App > More > Advanced > Smart DHCP.
6. Added a prompt notification when the Ethernet link rate goes down to 100Mbps.
7. Added schedule and bandwidth limit to guest network under Deco App > More > Wi-Fi > Guest Network.
8. Fixed the bug that the built-in speedtest has low speed test results.
Notes:
1. This firmware downgrade could be done via firmware recovery-How to use firmware recovery.
2. Please update your Deco APP to the latest version for the new features.
3. If there are non-1.6.0 models in the Mesh network, you may miss some new features but this feature will be supported via firmware update in the future.
4. You may miss some new features when Deco is set to Access Point mode.
Related Articles:
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
@David-TP Done submitting the logs as instructed. Let me know if this helps.
- Copy Link
- Report Inappropriate Content
@David-TP when can we expect the upgrade related to scheduled reboot for deco X20? I bought it new last week and not sure if i did a mistake!
- Copy Link
- Report Inappropriate Content
@David-TP I have new deco X20 with firmware
| X20(4.0) |
1.0.2 Build 20220401 Rel. 63997 |
Can I update my deco with 1.6.0 firmware?
- Copy Link
- Report Inappropriate Content
Hi, Thank you for your time and patience.
Sorry for the delay.
Deco X20-V4 could not use beta 1.6.0 firmware here and there has been further news about the 1.6.0 firmware for Deco X20 yet.
Have you noticed any performance issues with the current firmware 1.0.2 on Deco X20 V4?
Thanks a lot.
Best regards.
- Copy Link
- Report Inappropriate Content
@David-TP thanks for replying.
I don't see any performance issue but eagerly waiting scheduled restart feature for my mesh.
- Copy Link
- Report Inappropriate Content
Hi, In this way, it might still need a while for the support of the reboot schedule on Deco X20 V4.
If you have a smart Wi-Fi plug, it would be a workaround to use the smart plug to power up Deco and set up a power schedule on the smart plug.
Thank you very much.
Best regards.
- Copy Link
- Report Inappropriate Content
Is there a procedure to follow to update a Deco network with different hardware versions? I have 3 v1 M9 Decos that I've updated to the beta firmware and now I'd like to update my 2 v2.8 M9 Decos.
Do I need to remove the v2.8's from my network, build a stand-alone network with just the v2.8s, update the firmware and then add them back to my main network?
- Copy Link
- Report Inappropriate Content
@imakeholesinu you can go directly to each deco IP where you will find a web interface that allows you individual updates. I have at home 3 M9Plus Deco, two 2.0 and one 1.0 (meaning different firmware to apply) and that way worked fine. I hope that helps.
- Copy Link
- Report Inappropriate Content
I guess something must be different here because when I go to the IP addresses of what I suspect the new v2.8 Decos are I get a message from them saying
Not Found
The requested URL /webpages/login.html was not found on this server.
The IPs don't show up in my app for those new Decos either, just the MAC addresses.
- Copy Link
- Report Inappropriate Content
I decided to wait a few weeks until i updated to the beta just to make sure there werent any major bugs. Updated today and only one of the 4 updated via the web tool, but i was able to update the rest using the downloadable update tool. I did have to reset my zigbee smart devices and rescan, but they finally reconnected to the decos also. selecting signal source of mesh units is working as expected. so far so good. thank you tplink devs for adding the m9+ 1.6 beta
- Copy Link
- Report Inappropriate Content
Information
Helpful: 10
Views: 111633
Replies: 440
Voters 2
