Official Release Deco M9 Plus 1.6.4
Current Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.4_Build_20240718
Release Note:
1. Improve the device stability;
2. Enhance the system security
---------------------------------------------------------------------------------------------------
History Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.3_Build_20231225
Release Note:
1. Fix the potential security vulnerability and its related problem.
2. Improve system stability and security.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.2_Build_20230906
Release Note:
1.Fixed the bug that parental control doesn't take effect.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.1_Build 20230403
Release Note:
1. Added Reboot Schedule for every day/week under Deco App > More > Reboot Schedule.
2. Added support for customizing Satellite Deco Signal Source under Deco App > Internet > Select the Satellite Deco > Signal Source.
3. Added support for customizing clients Connection Preference under Deco App > CLIENTS > Select the client > Click the gear icon on the right-up corner > Connection Preference.
4. Added No-IP and DynDNS to the DDNS settings under Deco App > More > Advanced > DDNS.
5. Added Smart DHCP on/off switch in Access Point mode under Deco App > More > Advanced > Smart DHCP.
6. Added a prompt notification when the Ethernet link rate goes down to 100Mbps.
7. Added schedule and bandwidth limit to guest network under Deco App > More > Wi-Fi > Guest Network.
8. Fixed the bug that the built-in speedtest has low speed test results.
Notes:
1. This firmware downgrade could be done via firmware recovery-How to use firmware recovery.
2. Please update your Deco APP to the latest version for the new features.
3. If there are non-1.6.0 models in the Mesh network, you may miss some new features but this feature will be supported via firmware update in the future.
4. You may miss some new features when Deco is set to Access Point mode.
Related Articles:
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi, I see the V2 of your Deco M9 plus is on 1.2.12 and it might need to be updated to 1.6.0 via firmware upgrade utility:
Thank you very much.
- Copy Link
- Report Inappropriate Content
Thank you! After about 30mins I was able to get the tool to work and the V2.8 hardware was updated successfully. I am able to see the IP addresses of both devices and I am able to set which Deco they should connect to.
- Copy Link
- Report Inappropriate Content
I am upgrading to the latest update using For V2/2.2/2.6/2.8, Download link: Deco_M9_V2_1.6.0_220823
How long does this take? I started the upgrade but it keeps spinning and it says uploading. I have been waiting for about 15 minutes now since i hit upgrade. I don't see any progress bar.
- Copy Link
- Report Inappropriate Content
Thanks for the feedback.
I tested on my side and the firmware upgrade works quite normal.
It is suggested to update Deco one by one, starting from the satellite M9 first. An Ethernet connection is highly recommended.
Wait for your reply.
Best regards.
- Copy Link
- Report Inappropriate Content
I was able to install it. I just had to quit the initiated process after waiting for almost an hour and redo the firmware upgrade. Thank you David. I appreciate your hardwork on this.
- Copy Link
- Report Inappropriate Content
Dear David, it seems that the frequent disconnects and reconnects are not yet fixed in this August 23 version. I have a few devices which I have set an alert when they go online and offline. What could be the reason for this? I haven't done this offline/online notificafions for all my devices. It seems that this is a stability issue which everyone has been pointing out. I have attach above my screenshot of my notifications.
- Copy Link
- Report Inappropriate Content
I'm currently running version Deco_M9_V2_1.6.0_220823 on my M9Plus V2 (was the same issue with 220810) but haven't experienced this with 1.5.6.
The device disconnection is constantly happening when devices seem to be in range of 2 Decos.
Please see the screenshot of my alerts.
This is a huge issue, since it is draining the devices battery, interrupts phone calls over WiFi, slows down the Internet experience due to constantly reconnecting.
Thanks for a quick fix!
Please mention my phone reconnects every 3 to 5 minutes while just laying on the table.
- Copy Link
- Report Inappropriate Content
@HopSaSam have you tried turning off fast roaming. I'm not seeing this on any of my decos .
- Copy Link
- Report Inappropriate Content
Why should I?
I want to use all available features and not going back 10 years.
This is clearly a stability issue.
- Copy Link
- Report Inappropriate Content
@HopSaSam just trying to help identify what the issue is - fast roaming doesn't work properly with multiple devices. if its causing you dropped calls why not try turning it off - if it fixes it the benefits you'd lose are marginal
- Copy Link
- Report Inappropriate Content
Information
Helpful: 10
Views: 112184
Replies: 440
Voters 2
