New Release Deco M9 Plus 1.6.3
Current Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.3_Build_20231225
Release Note:
1. Fix the potential security vulnerability and its related problem.
2. Improve system stability and security.
---------------------------------------------------------------------------------------------------
History Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.2_Build_20230906
Release Note:
1.Fixed the bug that parental control doesn't take effect.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.1_Build 20230403
Release Note:
1. Added Reboot Schedule for every day/week under Deco App > More > Reboot Schedule.
2. Added support for customizing Satellite Deco Signal Source under Deco App > Internet > Select the Satellite Deco > Signal Source.
3. Added support for customizing clients Connection Preference under Deco App > CLIENTS > Select the client > Click the gear icon on the right-up corner > Connection Preference.
4. Added No-IP and DynDNS to the DDNS settings under Deco App > More > Advanced > DDNS.
5. Added Smart DHCP on/off switch in Access Point mode under Deco App > More > Advanced > Smart DHCP.
6. Added a prompt notification when the Ethernet link rate goes down to 100Mbps.
7. Added schedule and bandwidth limit to guest network under Deco App > More > Wi-Fi > Guest Network.
8. Fixed the bug that the built-in speedtest has low speed test results.
Notes:
1. This firmware downgrade could be done via firmware recovery-How to use firmware recovery.
2. Please update your Deco APP to the latest version for the new features.
3. If there are non-1.6.0 models in the Mesh network, you may miss some new features but this feature will be supported via firmware update in the future.
4. You may miss some new features when Deco is set to Access Point mode.
Related Articles:
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi, Actually I am informed that both 1.5.1 and 1.5.6 of Deco M9 plus are 100% released and pushed to the correct models. So you are supposed to get the firmware push notification or at least detect this version via "update Deco" on the APP. For the latter new firmware, the release portion is usually 30%, or even less in the beginning, but will add up over time. The only reason I could think of is that you might accidentally "skip this version" when the push message showed up.
If possible, you could click "update Deco" once(or maybe several times) on the APP, then please refer to this link to help me submit the APP log:
Thank you very much.
Best regards.
- Copy Link
- Report Inappropriate Content
Hi David,
E-mail sent to support with my configuration.
I use vlan tag 12, MEO Portugal ISP.
I don't downgrade for now and wait for support email feedback.
Thanks in advance
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Support call me by mail
They suggest to change cables, I did that, no success, and also to give a try changing the main deco with new cables, also with no success.
After that I downgrade again to 1.5.6 and get the correct bandwidth.
I also said that I will test anything they need, but get an answer that they will test in laboratory...
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
I have the 1.6.0 final version before they removed it and it works fine
- Copy Link
- Report Inappropriate Content
Hi guys,
I was in easter holidays. Tplink support send me a m9 plus firmware version 1.6.1 and everything is OK. Tested now.
I get full bandwidth from my ISP.
- Copy Link
- Report Inappropriate Content
Hey, could you please share the link?
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
It's better wait for TPLink to realise it for everyone.
I just send them an email to inform everything is OK.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 10
Views: 95656
Replies: 424
Voters 2
