Home Network Community > Deco > X20 Configuration Question
< Deco

X20 Configuration Question

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

X20 Configuration Question

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
X20 Configuration Question
X20 Configuration Question
2023-01-23 18:24:54
Tags: #Deco Ethernet Backhaul #Access Point Mode
Model: Deco X20  
Hardware Version: V2
Firmware Version:

My network is three X20s two of which are Model X20(US) Version 2.0 with the third being a Model X20(US) Version 1.20. One of the Version 2.0 units serves as the router connected to my cable modem with one Version 2.0 and one Version 1.20 serving as access points, both of which are backhauled. Green lights all around but I'm curious whether mixing the two versions in the same network is potentially troublesome. Thanks.

  0      
 
  0      
 
#1
Options
3 Reply
Re:X20 Configuration Question
2023-01-29 09:52:59

  @DecoRonn 

Hi， No, all Deco models are compatible with each other and they should work well in a mixed Mesh network.

But I do suggest using Deco X20 V1.2 as the main Deco.

Best regards.

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶Deco X50-5G-V1-1.2.0 Supports WireGuard VPN, Hybrid Mesh and More Try to leave a Message if urgent help is required.
  0  
  0  
#2
Options
Re:X20 Configuration Question
2023-02-16 03:29:04

  @David-TP 

I shall change my network so that the X20 V1.2 is the main Deco (router) as you suggest, but I would like to understand why. Thanks for your assistance

 

David-TP wrote

  @DecoRonn 

Hi， No, all Deco models are compatible with each other and they should work well in a mixed Mesh network.

But I do suggest using Deco X20 V1.2 as the main Deco.

Best regards.

 

  0  
  0  
#3
Options
Re:X20 Configuration Question
2023-02-16 07:03:55 - last edited 2023-02-16 07:04:20

  @DecoRonn 

Hi, Normally, the features supported on the Deco APP follow the main Deco.  For example. X20 V1.2 supports "Test internet speed" while Deco X20 v2 does not. You might not see this feature on the APP when Deco X20 V2 is the main Deco. 

But I noticed you mentioned Deco X20 was in the Access Point mode, not the default wireless router mode. There are fewer differences among different models when they are in AP mode. In this way, both V1.2 and V2 would be suggested to be set up as the main Deco.

Thank you very much.

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶Deco X50-5G-V1-1.2.0 Supports WireGuard VPN, Hybrid Mesh and More Try to leave a Message if urgent help is required.
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 534

Replies: 3

Tags

Deco Ethernet Backhaul Access Point Mode
Related Articles
Archer VR2100 configuration question
925 0
 Deco X20 port configuration
1310 0
 Config Question
430 0
 Configure Preferred Signal Source on X20
452 0
 Deco X20-DSL and IPTV configuration
2165 0
 x20 question
529 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.