Home Network Community > DSL Modem Routers > Falla de identificacion via cable a la pc no emana ninguna señal wifi, no puedo entrar a la terminal
< DSL Modem Routers

Falla de identificacion via cable a la pc no emana ninguna señal wifi, no puedo entrar a la terminal

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Falla de identificacion via cable a la pc no emana ninguna señal wifi, no puedo entrar a la terminal

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Falla de identificacion via cable a la pc no emana ninguna señal wifi, no puedo entrar a la terminal
Falla de identificacion via cable a la pc no emana ninguna señal wifi, no puedo entrar a la terminal
2024-02-14 05:07:30 - last edited 2024-02-27 09:28:02
Tags: #Network Connectivity #Installation #Firmware Update
Model: Archer VR300  
Hardware Version: V1
Firmware Version:

Compre un nuevo Tp- Link Ac 1200 de 300 Mbs para reemplazar el que ya tenia, pero al conectarlo no emanana ninguna señal inicial como wifi, luego al conectarlo a la pc, tampoco lo detecta y se mantiene en verificando conexion. Me sugirieron cambiar la direccion IP a estatica para poder acceder al router, pero nada a funcionado. 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Falla de identificacion via cable a la pc no emana ninguna señal wifi, no puedo entrar a la terminal-Solution
2024-02-23 03:26:18 - last edited 2024-02-27 09:28:02

  @Yo4nder 

 

Normally Power LED should be solid on after it boots up, and WiFi LED should be on as well, if it is still the same after factory reset, please check waranty and get it replaced, it seems to be a hardware issue.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#4
Options
3 Reply
Re:Falla de identificacion via cable a la pc no emana ninguna señal wifi, no puedo entrar a la terminal
2024-02-22 06:49:47

  @Yo4nder 

 

Hi, what about the LED status on the VR300? is the WiFi LED light up?

Please try reset the device to factory defaults by holding reset button/hole for about 10s until power LED flashing. Then check if any client device can see the default TP-Link WiFi.

If still no any WiFi signal, I am afraid the device is defective, you could contact the retailer to get it replaced.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#2
Options
Re:Falla de identificacion via cable a la pc no emana ninguna señal wifi, no puedo entrar a la terminal
2024-02-22 15:19:59

  @Luz solar Al encender el equipo la lu de encendido se mantiene parpadeando, el resto de las luces ninguna. Solo al conectar a la pc via Lan se enciende la luz de conexion. Sin embargo solo indica en la conexion "Red no identificada" por eso tampoco puedo entrar directamente al sistema interno para actualiar el fimware. ¿Existe algun otro metodo para flashear el fimware que no sea desde la configuracion interna? 

  0  
  0  
#3
Options
Re:Falla de identificacion via cable a la pc no emana ninguna señal wifi, no puedo entrar a la terminal-Solution
2024-02-23 03:26:18 - last edited 2024-02-27 09:28:02

  @Yo4nder 

 

Normally Power LED should be solid on after it boots up, and WiFi LED should be on as well, if it is still the same after factory reset, please check waranty and get it replaced, it seems to be a hardware issue.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 327

Replies: 3

Tags

Network Connectivity Installation Firmware Update
Related Articles
Deco P9 - can I connect my non-wifi PC via ethernet cable?
338 0
FALLA WIFI
247 2
Setting up AC2800 via Telstra Smart Modem
388 0
Falla para instalar la app tplink
307 0
Falla en instalacion del router
293 0
Tiene una falla la aplicación
408 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.