Official Release Deco X50/X55 V1 1.5.5 Optimize The Overall App Experience / Network stability
This Article applied to:
Deco X50/X55_V1/1.6_1.5.1/1.5.0
Firmware Download Link:
| Deco X50_V1/1.6 | 1.5.5_build_20240718 (Official Version) |
| Deco X55_V1/1.6 |
1.5.5_build_20240718 (Official Version) |
Update Advice:
1. Please make sure the Deco APP is up-to-date.
2. How to manually update the firmware via web UI- How to Update the Firmware of Deco.
Modifications and Improvement
1. Supported configuring IPv6 during setup.
2. Added the low-power feature.
3. Enhanced the VPN performance.
4. LED schedule feature supported control of individual device LEDs.
5. Improved the overall Deco App experience, especially with the online client list status.
6. Increased networking number.
7. Enhanced the system security.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
I'm surprise, on my DECO X50 it's seem to be up to date with teh 1.4.1 Build 20231122 Rel 40485 ??
- Copy Link
- Report Inappropriate Content
@David-TP the installation went smooth. I like that we can finally see the cpu and memory usage of the deco. Would be cool to see it with all of them though and not just the main.
LED schedule and individual settings per deco is nice.
Cant confirm about the client list since its always been running great for me.
- Copy Link
- Report Inappropriate Content
Hi, I think you could try to manually update the Deco X50_V1 from 1.4.1 to 1.5.5 via the web interface.
(the IP address of Deco X50 could be found on the Deco APP, such as,
Occasionally, due to unknown reasons, Deco APP might fail to receive the new firmware push notification.
Thank you very much and best regards.
- Copy Link
- Report Inappropriate Content
@David-TP Hi David, in my case (Deco X50 EU v1.0) the Deco app says my latest firmware is already installed. This is 1.4.1.
A while ago, 1.5.1 was available through app but I didn't install it due to issues other people reported.
Now, 1.5.5 is not available throughout app.
I looked in the webinterface and I also there it says 1.4.1 is the newest firmware.
Will 1.5.5 also be rolled out gradually or should it already be there right now?
nb : official TP link website of my region (EU) says 1.4.1 is latest software https://www.tp-link.com/nl/support/download/deco-x50/v1/#Firmware
- Copy Link
- Report Inappropriate Content
Good news the new firmawre1.5.5. is now also available
Now waiting for update on X50-OUTDOOR and XE200
- Copy Link
- Report Inappropriate Content
@Pascal_DECO_94 Hi Pacal, I see you are in France. Here in the Netherlands 1.5.5 is not available yet for Deco X50 v1.0 EU through the app.
can you let us know how the 1.5.5 update is performing? 1.5.1 was a great deal of trouble.
thank you
- Copy Link
- Report Inappropriate Content
I update 2 or m'y x50 using thé binary from support.
Ni issue. Its woek fine.
To do thé update i get thé IP of one box.. and log directely on it using a browser. Easy
- Copy Link
- Report Inappropriate Content
Thanks. I dont know i Can connect to each box 😉
- Copy Link
- Report Inappropriate Content
@Pascal_DECO_94 No instability or dhcp issues or disconnects , drop connections etc ?
- Copy Link
- Report Inappropriate Content
JanRekenaar wrote
@Pascal_DECO_94 No instability or dhcp issues or disconnects , drop connections etc ?
I had enormous problems with two devices on router firmware 1.5.1 and earlier—they were losing DHCP and having DNS issues, which caused the devices to lose connection with the router when they were reset, along with constant problems with Netflix or Disney+ (buffering, buttons not loading their thumbnails, and freezing on the end credits). After installing 1.5.3, the problems disappeared. I’ve now been running 1.5.5 since its release, and there are STILL NO PROBLEMS... Finally, at last... I recommend 1.5.5. I installed it manually through the web interface.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 17067
Replies: 146
Voters 0
No one has voted for it yet.