Deco S7 Network Disconnections
Hi,
Network
2 S7, 1 acting as Wifi Router but it is conected to an archer c80 who has the internet conection.
Can t change the configuration as i have more than 20 devices conected
Since last stable update the second Deco disconnects from network. Tried everything, Beta firmware, Reset and configure but nothing works
I m using only one Deco now.
Any idea?
(sorry about my english)
- Did you have the "red light" on both Deco S7 units?
No, just secondary one
- Is the satellite S7 wirelessly connected to the main Deco S7 into the Mesh system, or via an Ethernet cable?
wirelessly
I noticed you mentioned when Deco S7 was disconnected and turned red, the internet service was still working
No until you remove sencondary from the network
Do you have an ISP-provided router in front of the main Deco S7? or how did you test the internet connection from the ISP?
Yes, I tested it from a device connected to main router (Archer)
Similar case
https://community.tp-link.com/en/home/forum/topic/676316?replyId=1406122
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi, Have you tried to set Deco S7 into "Access Point" Mode:
How to set up Deco to work in Access Point mode
A: I m trying to avoid this cause y have more than 30 IOT devices conected, changing WIFI config to all of them would be extremely dificult.
I saw you were on the 1.5.1 beta firmware, not the official firmware and I don't think it is due to any firmware upgrade.
A: When this issue started I had the official firmware, then i read about the beta and installed it. The issue is the same with both releases but it started with the previous one.
Did you try to remove the satellite Deco S7 from the Mesh and add it again via Deco APP?
A: several times, at least 10
- If yes, can it be successfully added? Would it turn to flash red shortly after being online for a while?
A: exactly and wifi conection starts failing
In case there is something wrong with this satellite S7, when you don't need the internet service from S7, It is also suggested to set the secondary unit as the main Deco to see whether it works well: How to replace the main Deco with another Deco
A: It is also suggested to set the secondary unit as the main Deco to see whether it works well <<<< dont know why but its has been working for several hours, I´ll wait a couple of days and then mark this solution as good!
Thanks a lot!
Thank you very much and best regards.
- Copy Link
- Report Inappropriate Content
Hi, Thanks for the feedback.
Please try to disable "EasyMesh" on the Archer C80 first.
If it didn't help, since Deco S7 is also a wireless router, have you tried to remove C80 from the network and leave Deco S7 as the only router.
Wait for your reply and best regards.
- Copy Link
- Report Inappropriate Content
Q: Please try to disable "EasyMesh" on the Archer C80 first.
A: Done, but still not working
Q: If it didn't help, since Deco S7 is also a wireless router, have you tried to remove C80 from the network and leave Deco S7 as the only router.
A: Can´t do that, need the router to cover all areas, Something happened, Its been working fine for more than a year (probably firmware update
Hernan10ARG wrote
Hi,
Network
2 S7, 1 acting as Wifi Router but it is conected to an archer c80 who has the internet conection.
Can t change the configuration as i have more than 20 devices conected
Since last stable update the second Deco disconnects from network. Tried everything, Beta firmware, Reset and configure but nothing works
I m using only one Deco now.
Any idea?
(sorry about my english)
- Did you have the "red light" on both Deco S7 units?
No, just secondary one
- Is the satellite S7 wirelessly connected to the main Deco S7 into the Mesh system, or via an Ethernet cable?
wirelessly
I noticed you mentioned when Deco S7 was disconnected and turned red, the internet service was still working
No until you remove sencondary from the network
Do you have an ISP-provided router in front of the main Deco S7? or how did you test the internet connection from the ISP?
Yes, I tested it from a device connected to main router (Archer)
Similar case
https://community.tp-link.com/en/home/forum/topic/676316?replyId=1406122
)
Thanks
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Hi, Have you tried to set Deco S7 into "Access Point" Mode:
How to set up Deco to work in Access Point mode
I saw you were on the 1.5.1 beta firmware, not the official firmware and I don't think it is due to any firmware upgrade.
Did you try to remove the satellite Deco S7 from the Mesh and add it again via Deco APP?
- If yes, can it be successfully added? Would it turn to flash red shortly after being online for a while?
In case there is something wrong with this satellite S7, when you don't need the internet service from S7, It is also suggested to set the secondary unit as the main Deco to see whether it works well: How to replace the main Deco with another Deco
Thank you very much and best regards.
- Copy Link
- Report Inappropriate Content
Hi, Have you tried to set Deco S7 into "Access Point" Mode:
How to set up Deco to work in Access Point mode
A: I m trying to avoid this cause y have more than 30 IOT devices conected, changing WIFI config to all of them would be extremely dificult.
I saw you were on the 1.5.1 beta firmware, not the official firmware and I don't think it is due to any firmware upgrade.
A: When this issue started I had the official firmware, then i read about the beta and installed it. The issue is the same with both releases but it started with the previous one.
Did you try to remove the satellite Deco S7 from the Mesh and add it again via Deco APP?
A: several times, at least 10
- If yes, can it be successfully added? Would it turn to flash red shortly after being online for a while?
A: exactly and wifi conection starts failing
In case there is something wrong with this satellite S7, when you don't need the internet service from S7, It is also suggested to set the secondary unit as the main Deco to see whether it works well: How to replace the main Deco with another Deco
A: It is also suggested to set the secondary unit as the main Deco to see whether it works well <<<< dont know why but its has been working for several hours, I´ll wait a couple of days and then mark this solution as good!
Thanks a lot!
Thank you very much and best regards.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 389
Replies: 5
Voters 0
No one has voted for it yet.