Problem with displaying clients on a Deco X20 v4 fw 1.5.5 and Deco X50 v1 1.6.7

Problem with displaying clients on a Deco X20 v4 fw 1.5.5 and Deco X50 v1 1.6.7

Problem with displaying clients on a Deco X20 v4 fw 1.5.5 and Deco X50 v1 1.6.7
Problem with displaying clients on a Deco X20 v4 fw 1.5.5 and Deco X50 v1 1.6.7
2025-05-15 12:59:40 - last edited 2025-06-11 01:48:36
Model: Deco X20   Deco X50  
Hardware Version: V1
Firmware Version: 1.6.7

I have a problem with displaying clients on a Deco X20 v4 fw 1.5.5 and Deco X50 v1 1.6.7 connection. When clients are connected to X50, there are no problems. All clients are visible. When they go to the X20 access point, there is a problem with displaying. I cannot send logs from the application, since the page is banned. But I can attach them to my email if you open a ticket. There are no problems with firmware 1.6.1 X50 and X20. All clients are visible. Perhaps the mechanism has changed in 1.6.7 and now it needs to be edited in 1.5.5 X20?

I also noticed an inconvenience in the Deco application. When I went, out of interest, to the EasyMesh section, the application offered to add my network to the EasyMesh network and all network settings immediately flew off. The routers went into factory reset. And in the list of my networks, in the application - the network disappeared. maybe it's possible to do an undo mode somehow? I was able to restore by creating a new network and rolling out old settings from the cloud. But DDNS, VPN were not saved. Ports that are forced to be WAN were also not saved.

  0      
  0      
#1
Options
1 Accepted Solution
Re:Problem with displaying clients on a Deco X20 v4 fw 1.5.5 and Deco X50 v1 1.6.7-Solution
2025-05-16 02:13:24 - last edited 2025-06-11 01:48:36

  @xplodzs 

@Festijn 

 

Hi, thank you for the feedback.

It is recommended to test the beta versions here:

https://community.tp-link.com/en/home/forum/topic/734426

Best regards.

Recommended Solution
  0  
  0  
#4
Options
6 Reply
Re:Problem with displaying clients on a Deco X20 v4 fw 1.5.5 and Deco X50 v1 1.6.7
2025-05-15 15:10:03

  @xplodzs I have a similiar problem with my deco's x50 and firmware version 1.6.4

 

New clients who connect to my network are no longer reported and visible!

So I have no control anymore of unwanted intruders.

 

Today I tested with a new device on my network which did a big download.

You can only see the general high download number on the deco but when you go to that deco the new client with is not visible.

 

Can someone advise how to solve this issue?

I have even payed for homeshield protection via deco app but feel that my network is exposed now cause I have no notifications and control of new clients anymore.

 

thx

  0  
  0  
#2
Options
Re:Problem with displaying clients on a Deco X20 v4 fw 1.5.5 and Deco X50 v1 1.6.7
2025-05-15 15:58:52

  @Festijn 1.6.7 X50 v1 firmware - everything is fine on it. X50+X20 bundle does not work

  0  
  0  
#3
Options
Re:Problem with displaying clients on a Deco X20 v4 fw 1.5.5 and Deco X50 v1 1.6.7-Solution
2025-05-16 02:13:24 - last edited 2025-06-11 01:48:36

  @xplodzs 

@Festijn 

 

Hi, thank you for the feedback.

It is recommended to test the beta versions here:

https://community.tp-link.com/en/home/forum/topic/734426

Best regards.

Recommended Solution
  0  
  0  
#4
Options
Re:Problem with displaying clients on a Deco X20 v4 fw 1.5.5 and Deco X50 v1 1.6.7
2025-05-16 06:45:43

  @David-TP already install / maybe there is a new firmware for x20 v4?

Living Room

X50(1.0)

1.6.7 Build 25031412 Rel. 48241

-

Bedroom

X20(4.0)

1.5.5 Build 20241231 Rel. 41749

  1  
  1  
#5
Options
Re:Problem with displaying clients on a Deco X20 v4 fw 1.5.5 and Deco X50 v1 1.6.7
2025-05-19 11:58:31

  @xplodzs 

Hi, thank you very much for the update.

There is a 1.6.6 version for Deco X20_V4, which is quite similar to the 1.6.7 version.

Later, if you need to revert from 1.6.6 to the original 1.5.5, a firmware recovery is needed.

If you want to test this version, you can find it in the private message.

Thank you very much.

Best regards.

 

 

  0  
  0  
#6
Options
Re:Problem with displaying clients on a Deco X20 v4 fw 1.5.5 and Deco X50 v1 1.6.7
2025-06-10 09:20:39
everything is fine with this firmware. no errors and all devices are visible!
  1  
  1  
#7
Options