Early Access Deco BE65/BE63/BE11000_V2_1.3.0 Added DoH & DoT, Speed Limit and Internet Backup
This Article Applies to:
Deco BE65(EU/US/AU/CA/UK)_V2.0
Deco BE63(US)_V2.6
Deco BE11000(US)_V2.6
Hey Everyone!
We are excited to announce a pre-release firmware update introducing DoH & DoT, Speed Limit, and Internet Backup, as well as other advanced features for Deco BE65/63/BE11000. We encourage users to install this firmware and share their feedback with us.
Firmware Modifications
New Features/Enhancements:
- Supported fixing a specific port as the WAN port.
- Added Hybrid Mesh feature.
- Added Internet Backup feature.
- Added DoH & DoT feature.
- Added Speed Limit feature for client devices.
- Optimized HomeShield feature.
- Improved System Stability.
Bug Fixes:
- Fixed the issue where the Online List doesn't show IP addresses of connected clients when Deco is in AP mode.
- Resolved the issue where the Qos Total Bandwidth doesn't take effect as expected under certain circumstances.
- Addressed the issue where the Deco may restart automatically under certain circumstances.
Download Link:
Deco BE65/BE63/BE11000_V2.0/V2.6 |
1.3.0_build_2026012212_rel11551_Beta 2026.2.13 updated |
Update Notice:
- Please be sure you have read the Beta Test Agreement before upgrading the Pre-release firmware!
- Please make sure the Deco APP is up-to-date.
- This firmware can’t be degraded directly to the previous 1.2.10/1.2.0 version.
- How to manually update the firmware via web UI.
As always, we value your feedback. If you happen to encounter any concerns during or after the firmware upgrade, please feel free to comment below with the following information. Your input helps us continue to improve and provide the best possible products and support.
- Provide a detailed network layout, including how the devices are connected.
- Include a detailed description of the issue and as much information as possible regarding the specific conditions that seem to trigger the behavior.
Thank you for your continued support and for being part of our community.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
@David-TP I have 3 BE11000 Deco units using Wi-Fi backhaul.
I also experienced issues on a chromebook and an ecobee smart thermostat. On different days and they seemed to work ok the next day. It appeared as though they were losing internet access w/o disconnecting from the Wi-Fi and it would connect and then disconnect every few seconds. On the ecbobee, music through Alexa was stutering and the Chromebook would say no internet and then it would work and it would be a cycle like that every few seconds.
The DL110 door lock appeared to be working yesterday evening even when I tried to recreate the issue by disabling the 2.4Ghz on my main network. The door lock now still saw the IoT SSID. When reenabling the 2.4Ghz on the main network, that SSID was also found.
I sent the email yesterday evening as instructed with the subject and url in body, but I have not heard back yet. I will let you know when I do.
- Copy Link
- Report Inappropriate Content
Hi David, I have updated to the refreshed version of 1.3.0 and there are a few bugs.
1. I have a 3 Deco set, one is connected via ethernet. In the app it shows as connected wirelessly.
2. Within ithe Deco app, in nternet connection, all IPv4 settings are not dispplayed, IP Address, Subnet Mask, and all others including DNS address all display as --. IPv6 settings page is fine.
3. Testing internet speed within thre Deco app does not work, It displays a red X, and says the network maybe slow than internet speed.
I hope the above can be resolved urgently.
Last question, what is the different between this newly released firmware, and the one that is BETA, which includes the heat map, v 1.3.0_build_20260211_beta this is located on a sperate post onn the support site.
- Copy Link
- Report Inappropriate Content
In addition to my post above,
1. Intermittently unable to connect to Deco app, when you can, says offline,
2. Ethernet backhaul does not work at all now.
3. Clients connected to Deco via ethernet are now offline and are unable to connect, even thought the Deco is displaying a green online light.
How can things go so badly. The previous firmware was pretty good, and this updated version which appears to only resolve NAT lookback issue now has MANY bugs.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Hi, I'll remove the beta first and report to the engineers for confirmation.
By the way, the 1.3.0 firmware I updated here yesterday is not the same version as the Deco BE65 heatmap beta:
1.3.0_26021212-rel47291 is the one to fix the NAT Loopback issue based on the previous 1.3.0_build_2026012212_rel11551
1.3.0_26021112-rel24761 is the beta with Heatmap. As far as I know, it hasn't included the NAT Loopback fix.
Thank you very much.
Best regards.
- Copy Link
- Report Inappropriate Content
Hi David. I am still using the Beta release 11551 which seems OK for me. However, I have noticed that when I try to open my Google Nest speaker group, to check what is in the group, I get a message that says my mobile phone must be connected to the same wifi network in order to view the speaker group... my phone is connected to the same wifi network and I am trying to view the speaker group whilst I am at home. I first saw this issue shortly after trying the beta release 11551, but can't be sure it is the reason as Google might have also changed something.
- Copy Link
- Report Inappropriate Content
@David-TP where can i download 1.3.0_26021212-rel47291
- Copy Link
- Report Inappropriate Content
@David-TP where can i download 1.3.0_26021212-rel47291 ???
I can downgrade for firmware 1.2.10 ???
- Copy Link
- Report Inappropriate Content
Information
Helpful: 2
Views: 6975
Replies: 78
Voters 2
