Early Access Deco BE65/BE63/BE11000_V2_1.3.0 Added DoH & DoT, Speed Limit and Internet Backup
This Article Applies to:
Deco BE65(EU/US/AU/CA/UK)_V2.0
Deco BE63(US)_V2.6
Deco BE11000(US)_V2.6
Hey Everyone!
We are excited to announce a pre-release firmware update introducing DoH & DoT, Speed Limit, and Internet Backup, as well as other advanced features for Deco BE65/63/BE11000. We encourage users to install this firmware and share their feedback with us.
Firmware Modifications
New Features/Enhancements:
- Added WiFi Heatmap. (It also requires the Deco App version to be: 3.10.133 for IOS and 3.10.80 for Android.)
- Supported fixing a specific port as the WAN port.
- Added Hybrid Mesh feature.
- Added Internet Backup feature.
- Added DoH & DoT feature.
- Added Speed Limit feature for client devices.
- Optimized HomeShield feature.
- Improved System Stability.
Bug Fixes:
- Fixed the NAT Loopback issue.
- Fixed the issue where the Online List doesn't show IP addresses of connected clients when Deco is in AP mode.
- Resolved the issue where the Qos Total Bandwidth doesn't take effect as expected under certain circumstances.
- Addressed the issue where the Deco may restart automatically under certain circumstances.
Download Link:
Deco BE65/BE63/BE11000_V2.0/V2.6 |
1.3.0_build_2602261_rel_21001_Beta 2026.3.9 updated |
Update Notice:
- Please be sure you have read the Beta Test Agreement before upgrading the Pre-release firmware!
- Please make sure the Deco APP is up-to-date.
- This firmware can’t be degraded directly to the previous 1.2.10/1.2.0 version.
- How to manually update the firmware via web UI.
As always, we value your feedback. If you happen to encounter any concerns during or after the firmware upgrade, please feel free to comment below with the following information. Your input helps us continue to improve and provide the best possible products and support.
- Provide a detailed network layout, including how the devices are connected.
- Include a detailed description of the issue and as much information as possible regarding the specific conditions that seem to trigger the behavior.
Thank you for your continued support and for being part of our community.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
I used this one 47291
https://static.tp-link.com/upload/beta/2026/202602/20260213/BE65V2_BE65V3_V2-ver1-3-0-P1%5B26021212-rel47291%5D.zip
but I prefer
11551
- Copy Link
- Report Inappropriate Content
@iresLeandro Thank you, but why you prefer the 11551????
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
+100 for this.
If you go back a few posts, you'll see the issues I had after installing 1.3.0 rel. 47291, reverting back to 1.3.0 rel. 11551 I'm at least able to use the network correctly, however DoT still doesn't work, so I'm using DoH.
- Copy Link
- Report Inappropriate Content
I've been running the above Beta firmware on two BE65v2's for weeks without issue until just now. For no apparent reason, my WiFi died at approximately 18:55 and both devices became unreachable via the app. I had to disconnect both from mains power for a minute or two to get them up and running again.
The basics: Deco’s are connected via Ethernet. IoT, MLO and DoH is enabled. My network is configured to use the Allow List Mode.
- Copy Link
- Report Inappropriate Content
Hi, did you remember the LED status on the two Deco BE65s? Were they solid/flashing red?
It would help if you save a copy of the web UI system log(before restarting the Deco or making any changes), then submit the Deco App log together with the web system log to us next time, so that the engineer can further check whether it is just an accident or a potential bug.
Thank you very much.
Best regards.
- Copy Link
- Report Inappropriate Content
@David-TP, the LEDs were solid green but all three SSIDs weren’t showing. Our wired desktop PC also had no internet. I tried accessing the web GUI via its 192.168.0.1 IP address but it wouldn’t load the page. I had to disconnect the power from both units several times before they finally worked again.
- Copy Link
- Report Inappropriate Content
Hi again David
I noticed that every time the edge device (from the internet provider) is reset, the Deco BE65 devices continue to work, but the Wi-Fi speed drops to very low values. Restarting the devices is necessary, and only then does everything return to normal. I have a 1 Gbps connection in both directions and use rel.11551.
- Copy Link
- Report Inappropriate Content
I've been using rel.11551 for about a week now, and my only problem is that DOT isn't working. I'm using NextDNS, and while the setup successfully establishes and saves the connection without any errors, it's not working. No queries are coming through, and ads aren't being blocked.
- Copy Link
- Report Inappropriate Content
as I reported earlier in this thread, and direct to TP Link, I have the same issue but using Cloudflare DoT, accepts the address and tests fine via the deco app, but doesn't work on clients. I've reverted to using DoH which is working.
There's also a few other little bugs, hopefully a newer version is out soon to resolve these.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 3
Views: 16441
Replies: 132
Voters 2
