How to set up Ethernet Backhaul with Deco M4

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

How to set up Ethernet Backhaul with Deco M4

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
How to set up Ethernet Backhaul with Deco M4
How to set up Ethernet Backhaul with Deco M4
2019-03-08 08:17:11
Model: Deco M4  
Hardware Version:
Firmware Version: 1.0.6

I setup the M4 with wired them together. 

The speed test on Device 2 is never more than 100mbps 

What's wrong ?

 

But when test with wireless , It's ok.

 

 

  0      
  0      
#1
Options
6 Reply
Re:How to set up Ethernet Backhaul with Deco M4
2019-03-08 09:27:16

Hi Natsu,

 

have you checked the speed settings of your switch?

 

Cheers

 

Holger

  0  
  0  
#2
Options
Re:Re:How to set up Ethernet Backhaul with Deco M4
2019-03-08 09:31:09

No switch on my network

 

Deco M4 .   Unit 1  connect to internet  by wire 1g.

Deco M4 .  Unit 2 connect to  Unit 1 by wire 1g.

 

This should be Ethernet Backhaul option.

 

 

the speed test with wireless 5Ghz on Unit 2. never more than 100 Mbps

  0  
  0  
#3
Options
Re:How to set up Ethernet Backhaul with Deco M4
2019-03-09 17:25:36

anyone use deco M4

  0  
  0  
#4
Options
Re:How to set up Ethernet Backhaul with Deco M4
2019-03-12 06:15:13

Hello,

 

So you can get 1Gbps from each M4 by wired cable, while no more than 100Mbps from the wireless 5GHz from the 2nd unit, right? 

 

May I know what is the speed you can get from the main Deco by wirelessly? And who is your ISP and the bandwidth you paid? 

 

With your device connected to the 5GHz, it is suggested to disable QoS by device, clear the high priority devices and then test the speed again. 

 

Meanwhile, please check its wireless link speed as the below instruction: 

https://www.tp-link.com/en/faq-2265.html

 

Good day. 

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#5
Options
Re:How to set up Ethernet Backhaul with Deco M4
2019-11-05 00:00:53

@Kevin_Z 

 

Thanks for your answer. I have a similar issue. When I´m connected trough the modem the Speed is 220.45Mbps but when connected with the main DECO, both on WiFi and the laptop in the same place,  the speed decrease 35% as shown in the image below. The distance between the modem and the DECO is no more than 1.2m.

 

The issue get`s worse when i connect throug the third DECO (3r floor), the speed goes to less than 10 Mbps.

 

Thanks for your support. 

 

Andres

 

  0  
  0  
#6
Options
Re:How to set up Ethernet Backhaul with Deco M4
2019-11-05 01:46:37

@osmarul 

 

We will get some details to do further analysis and try to fix it. 

 

What is the current network topology/layout? And may I know who is your internet service provider? And what's the bandwidth you pay for them?

 

With your device connected to modem and main Deco by wired cable directly, please click here to check the wired negotiation speed.
Note: The steps are the same, while you need right click on local area connection or ethernet connection.        

                                                                  
Besides, please try to run a speed test via the Deco app and show us the results. 

 

Try to change DNS server under advanced>>IPv4>>Internet connection type and uncheck obtain DNS automatically and change the primary DNS to 8.8.8.8 and click save.

 

And try to disable fast roaming and set QoS as standard and clear all the high priority rules.

 

After that, please run the speed test again and check whether it work.

 

Have a great day.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#7
Options

Information

Helpful: 0

Views: 17202

Replies: 6

Related Articles