Home Network Community > All Threads > Xe75 and VM Hub3 Instant Issues
< All Threads

Xe75 and VM Hub3 Instant Issues

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Xe75 and VM Hub3 Instant Issues

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Xe75 and VM Hub3 Instant Issues
Xe75 and VM Hub3 Instant Issues
2023-06-25 12:27:59
Model: Deco XE75  
Hardware Version:
Firmware Version:

I have a constant issue with my xe75 and virgin media hub 3, which any time either is reset or there is a break in the Internet connection (virgin can be a bit unstable), the xe75 will not recognise the virgin media Internet connection again until it is reset.

 

I've got a unmanaged hub connected to my main deco as well, not sure if this is causing the issue? I think the deco may be not correctly auto sensing and then allocating the unmanaged hub as the wan port?! Is there any way to force/specify the WAN port? 

 

My Virgin Hub 3 is set up in modem mode and my decos are set in Wifi Router mode. 

  0      
 
  0      
 
#1
Options
3 Reply
Re:Xe75 and VM Hub3 Instant Issues
2023-06-25 17:58:58

  @10ken01 

 

Hey

 

The hub is likely a good part of your issue, WAN ports are designed to be direct connected and not via a switch or hub.  If possible direct connect the WAN port and use the hub on the second LAN port.

 

In answer to your question about sensing.. its along those lines.  More when the router resets the Deco isnt aware of this as the port doesnt drop at its side (still connected to the hub which is ACTIVE) therefore doesnt know to reset / restart a connection again.  If directly connected it may be better at detecting this as it will see the drop.

 

In terms of forcing WAN port, sadly not

  0  
  0  
#2
Options
Re:Xe75 and VM Hub3 Instant Issues
2023-06-26 04:54:11

  @Philbert 

 

Both the modem and the switch are connected directly to the main Deco, so there is nothing between the modem and the deco. 

 

I think that if the Internet drops, then the Deco tries to take Internet from the switch somehow and won't recognise when the Internet is back online from the modem. Is there any fix? 

 

Are there any beta firmwares which could help fix this? 

  0  
  0  
#3
Options
Re:Xe75 and VM Hub3 Instant Issues
2023-06-26 06:56:18

  @10ken01 

Hi, I see you mentioned earlier the switch is unmanaged, if Deco suddenly tried to recognize the switch port as the WAN port, you must have a device that is capable of assigning IP addresses connected to the switch. (For How the WAN/LAN auto-sensing works, please refer to WAN/LAN auto-sensing )

May I know the model number of the devices that are connected behind the switch?

To simplify the network topology, it is also suggested to temporarily remove the switch from the main Deco. (If it must be connected to the network, you could connect it temporarily to one of the satellite XE75s.)

 

Besides, can I have more details about the disconnection?

Would the main Deco XE75 turn to solid red?

If possible, could you please help me save a picture of the IPV4 page when the internet was disconnected?

(It is also suggested to refer to this link(Fix unstable connection when connected to the Deco network) to help me check which case is quite like yours.

 

Thank you very much.

best regards.

 

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶Deco X50-5G-V1-1.2.0 Supports WireGuard VPN, Hybrid Mesh and More Try to leave a Message if urgent help is required.
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 390

Replies: 3

Related Articles
XE75 Pro many issues
5018 0
Deco M5 on VM HUB3 in modem mode but BQM solid red
1095 0
Archer C60 and VM Super Hub 3
4598 0
XE75 security Issues
769 2
Deco XE75 issues
524 1
Deco XE75 Issues
1023 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.