Home Network Community > All Threads > Wired device not seen on main device. M4
< All Threads

Wired device not seen on main device. M4

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Wired device not seen on main device. M4

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Wired device not seen on main device. M4
Wired device not seen on main device. M4
2023-08-29 11:53:11 - last edited 2023-08-29 11:55:09
Model: Deco M4  
Hardware Version: V2
Firmware Version: 1.5.8

I have a set of three Deco M4 devices, configured as Access Points.

On one of the Deco M4 devices I connected a Synology NAS by wire.

in the deco app the device was always visible, until I set that deco M4 device as my master device.

I can see wired devices connected to the remote nodes, but not if connected to the main device. Anybody else with the same experience? 
edit: The NAS is working fine, but just not seen in the deco app.

 

  1      
 
  1      
 
#1
Options
4 Reply
Re:Wired device not seen on main device. M4
2023-08-30 06:18:02

  @RobinNL 

Hi, welcome to the community.

Are these 3 Deco M4 connected via Ethernet Backhaul?

Would there be any network switch involved?

And Could you please refer to this link to help me submit the Deco APP log:

How to submit Deco APP log

Thank you very much and best regards.

 

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶Deco X50-5G-V1-1.2.0 Supports WireGuard VPN, Hybrid Mesh and More Try to leave a Message if urgent help is required.
  0  
  0  
#2
Options
Re:Wired device not seen on main device. M4
2023-08-30 07:49:24

  @David-TP 

The new primary device is using two ports: the first one is connected to my ASUS router (the rest of my network is connected to a 16P gigabit switch also connected to the router).

the second port is connected to my NAS. I also switched ports, it doesn't change anything I see.

Before I set this node as the master device, the NAS was visible as a wired device. The port to the router / switch was never shown in the deco app. I have one other node with a wired backhaul, connected via a cable to the switch.

I have two other nodes (I added 1 extra to the set of three for the garden) connected wirelessly. When I now connect a device (like my laptop) to the second node it shows the device as wired, I think in the past when this one was my master node it also was not showing anything that was connected to it. I will check for the log upload,

  0  
  0  
#3
Options
Re:Wired device not seen on main device. M4
2023-08-30 09:17:54

I just uploaded the log files.

  1  
  1  
#4
Options
Re:Wired device not seen on main device. M4
2023-08-31 02:43:24

  @RobinNL 

Hi, Thanks for the update.

the logs have been received and forwarded to the engineers for further assistance.

Please check the email for further suggestions.

Best regards.

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶Deco X50-5G-V1-1.2.0 Supports WireGuard VPN, Hybrid Mesh and More Try to leave a Message if urgent help is required.
  0  
  0  
#5
Options

Information

Helpful: 1

Views: 442

Replies: 4

Related Articles
can m5 as main device can work with m4?
467 0
Which should be main device?
253 0
Fixed IP address for the second Deco M4 device
5897 0
priority device
1185 0
Deco m4 device loosing internet
400 1
Wired Device Disconnected
487 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.