HS110 Incorrect Energy Readings
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
I notice a problem with the energy tracking for my HS110, which is connected to my pool pump. The device is tracking time just fine.
Today: 6.98 hrs
Past 7 days: Daily Average 7.03 hrs Total Runtime 49.2 hrs
Past 30 days: Daily Average 7.02 hrs Total Runtime 211 hrs
If you look at the energy though:
Today: 4.92 kWh (about right)
Past 7 days: Daily Average 304 kWh Total Consumption 2130 kWh
Past 30 days: Daily Average 74.6 kWh Total Consumption 2239 kWh
You'll note that total consumption for 7 days is 2130 kWh. That's 2.1 MEGA WATTS!!! I don't think so!
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi, you can check the power of your pool pump and it's running time and calculate the power consumption manually, then compare the two values.
- Copy Link
- Report Inappropriate Content
Stella.Q wrote
Hi, you can check the power of your pool pump and it's running time and calculate the power consumption manually, then compare the two values.
Yeah, did those calcs and the HS110 is way off! My whole electricity bill for the entire house for the month is 600 kWh. The HS110 is indicating in the last 30 days it's consumed 2,200 kWh, three times my bill for the month and it's only a 700w motor! If it ran 24 hours a day for 30 days that would equal .7 * 24 * 30 = 504 kWh, no where near 2,200 kWh. The HS110 is clearly wrong but only the weekly calc and the 30 day calc. The daily figures look correct.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
MikeP wrote
Looks like the total power values might be missing a decimal point, e.g. 30.4kWh vs 304.
@MikeP If I've done the maths correctly, it should be reading
Today - 4.92 kWh, 0.7kWh * 7 hours = 4.9 kWh which is correct
Daily Average for the past 7 days should read 4.9 kWh, reading is saying 311 kWh which is not even close and 31.1 is too low if you move the decimal point
Total Consumption for the past 7 days should be 34.3 kWh (4.9 * 7), reading is saying 2175 kWh which is not even close and moving the decimal place doesn't work
Daily Average for the past 30 days should read 4.9 kWh, reading is saying 76.2 kWh which is not even close
Total Consumption for the past 30 days should be 147 kWh (4.9 * 30), reading is saying 2285 kWh which is not even close and moving the decimal place doesn't work
I do notice that Daily average for 7 days (311 kWh) time 7 does equal 2177 kWh which is close to 2175 and the Daily average for 30 days 76.2 * 30 = 2286 which is very close to the 2285, so I assume the problem is with the 7 day average and the 30 day average.
I think what I may do is do a hard reset of the plug, set it up again and see what happens.
- Copy Link
- Report Inappropriate Content
Thanks for the info. You may try to restart the plug or factory reset it, the way to factory reset it is pressing the top button for 10 seconds.
If it is possible, try to connect another appliance to the plug to do the comparison test.
Good day.
- Copy Link
- Report Inappropriate Content
Hi,
Sorry to dug up this but i also have the same issue
In 3 plugs, 2 of them are always doing that even with resets
https://i.imgur.com/fRdiGuR.jpg
- Copy Link
- Report Inappropriate Content
Hi, I am sorry that I could not open the link you have sent.
Would it be possible for you to attached the picture directly on the forum?
Thank you very much.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@Xaser Hello,
Sorry for the late response. Thank you for the photo, the power consumption is quite beyond the normal range.
Please check my private message and install a debug tool and help collect the log of the smart plug, thank you
You could try some basic troubleshooting here:
1. factory reset plug : with plug powered on, press ' settings' (looks like a gear) for more than 5 secs ( skip this step if you have tried factory reset )
2. try a different wall socket
3. confirm plug's firmware is up to date (kasa app -> settings-> firmware update) and also Kasa app is up to date
Thank you in advance.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 2961
Replies: 9
Voters 0
No one has voted for it yet.