Las acciones inteligentes fallaron con el interruptor
Hello,
I have the following switches in one room:
Two light bulbs with separate 3-way switches (HS210), Each Kasa switch (3-way) is connected to a non-smart 3-way switch.
One switch (HS200) with no light bulb connected.
Circuit A:
HS210 - Non-smart Switch: Connected to bulb A
Circuit B
HS201 - Non-smart switch: Connected to bulb B
Circuit C
HS200 - it doesn't have a light bulb
Smart Actions
1- If bulb A lights up, turn on HS200 (circuit C)
2- If bulb B lights up, turn on HS200 (circuit C)
3- If bulb A and bulb B are off, turn off Circuit C (HS200)
4- If you turn on the HS200 switch (Circuit C), light bulbs A and B will turn on
5- If the HS200 switch (Circuit C) is turned off, turn off bulbs A and B
These smart actions have been working smoothly for several months.
Previously, Circuit C (HS200), when it was turned on by rule 1 or 2, did not execute the associated intelligent action, this made it work perfectly, but now when executing rule 1 or 2 it executes the associated intelligent action, and this as indicated did not happen.
Can you tell me what is happening, if it is due to an update, can it be reversed?
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
We've applied some relevant modifications and this problem has been fixed now.
You may want to test your automation again and see how it works now.
- Copy Link
- Report Inappropriate Content
Are you saying it the other way around? Your current description seems a bit contradictory. The current problem seems to be that rule 1 and rule 2 are not executing, correct? Specifically, when bulb A or B is turned on, the HS200 does not activate?
If that's the case, please confirm whether the HS200 can still be controlled remotely (e.g. using cellular data) in the Kasa app. The automation won't run if the smart device has disconnected from the cloud (local only).
- Copy Link
- Report Inappropriate Content
Hello,
Hello,
I mean, when the HS210 is physically activated, bulb A is activated. It executed the intelligent action of turning on the HS200, but the intelligent action associated with it wasn't executed. However, it has been executing it for the past couple of days, and this corrupts the action it needed to execute.
- Copy Link
- Report Inappropriate Content
Can you send the device Mac address of these three switches to me through private message? Our support team can help to check it.
- Copy Link
- Report Inappropriate Content
We've applied some relevant modifications and this problem has been fixed now.
You may want to test your automation again and see how it works now.
- Copy Link
- Report Inappropriate Content
@Wayne-TP
Hello,
The MAC addresses were sent by private message: OK
Of the 5 smart actions, there is one that still doesn't work well, it is this one:
3- If bulb A and bulb B are off, turn off Circuit C (HS200)
When adding two triggers, it used to work as an "and" operator, but now it works as an "or" operator.
It might be an improvement to be able to choose whether it's the 'and' or 'or' operator.
Thanks,
- Copy Link
- Report Inappropriate Content
The trigger is always in the 'OR' logic, this hasn't been changed.
Actually you might consider syncing your Kasa devices to the Tapo app for management. Tapo offers more advanced automation settings, such as the new 'If' condition in automations. Check here to learn more skills about Tapo Smart Action. How to create Smart Action (Automation or Shortcut) on Tapo app
- Copy Link
- Report Inappropriate Content
Hello,
It worked for me as a logical AND.
Wayne-TP wrote
The trigger is always in the 'OR' logic, this hasn't been changed.
Actually you might consider syncing your Kasa devices to the Tapo app for management. Tapo offers more advanced automation settings, such as the new 'If' condition in automations. Check here to learn more skills about Tapo Smart Action. How to create Smart Action (Automation or Shortcut) on Tapo app
I'm going to check out the Tapo app and write about the results when using it.
Thank you for your attention and collaboration.
- Copy Link
- Report Inappropriate Content
Hello,
I already logged into the Tapo app and set the 'If' condition for the smart action that was failing, and now all 5 smart actions are working fine.
My nearly 20 Kasa devices are now visible in the Tapo app. I just had to reconfigure the rooms. The Google Home and Alexa settings remain the same.
Thanks for the help.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 508
Replies: 9
Voters 0
No one has voted for it yet.