Smart Home Community > All Threads > HS210 Wiring (Using only 1 HS210) - Stumped
< All Threads

HS210 Wiring (Using only 1 HS210) - Stumped

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

HS210 Wiring (Using only 1 HS210) - Stumped

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
HS210 Wiring (Using only 1 HS210) - Stumped
HS210 Wiring (Using only 1 HS210) - Stumped
2019-09-06 13:58:43
Model: HS210  
Hardware Version:
Firmware Version:

Ive been trying to setup the HS210 replacing only 1 of the dumb switches with an HS210.  Ive seen many success reports about this an the TP link app seems to support it as well.

 

So I've been trying to install an HS210 3 way switch. I'm replacing only one of my dumb switches. However when I hook it up like in the drawing , the tplink switch powers on but pressing it didn't turn the light on. I hear the relay in the switch clicking however.

If I turn the dumb switch on it turns on the lights but kills power to the tplink switch.

I've updated the tplink switch firmware to the latest and set it up in the app .

I've also tried to swap the red and black wires shown in the diagram but that did not help.

The original dumb switch configuration behaved as though both switches could control the light (no master/slave)

Any suggestions?

File:
6KJLByx.jpgDownload
  0      
 
  0      
 
#1
Options
5 Reply
Re:HS210 Wiring (Using only 1 HS210) - Stumped
2019-09-06 13:59:27

Here is how the dumb switches are wired (both have the same wiring configuration) and both dumb switches can independantly control the state of the lights.

File:
RnFDDPJ.jpgDownload
  0  
  0  
#2
Options
Re:Re:HS210 Wiring (Using only 1 HS210) - Stumped
2019-09-06 23:11:29 - last edited 2019-09-06 23:23:43

The red and white are the travelers. Black is the load.

You do not have a neutral.

There never is a neutral connected to a dumb switch.

  0  
  0  
#3
Options
Re:HS210 Wiring (Using only 1 HS210) - Stumped
2019-09-11 09:23:29 - last edited 2019-09-11 09:25:08

@JohnnyRockets 

 

HS210 can work with an ordinary/dumb switch, however, the HS210 must connected to the Live wire in the circuit.

 

And you connect one of the traveller wired to the electrical wire, have you ever tried to connect both of them?

 

Below is the installation guide you can have a reference.

https://www.tp-link.com/support/faq/2009/

 

Good day. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#4
Options
Re:HS210 Wiring (Using only 1 HS210) - Stumped
2019-09-11 13:13:46

@Kevin_Z 

 

Im installing the smart switch in a 3-gang box with 2 other switches controlling other lights. These are all on the same breaker. Would I be able to tap into a live wire (neutral) from one of these instead?

  0  
  0  
#5
Options
Re:HS210 Wiring (Using only 1 HS210) - Stumped
2019-09-12 09:52:26

@JohnnyRockets 

 

For your information, the HS210 is a three way switch; usually it is used as a pair; however, we can use it with an ordinary 3-way switch.

 

But to use the smart switch, it has to connect to the live wire. 

 

Good day. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#6
Options

Information

Helpful: 0

Views: 5205

Replies: 5

Related Articles
Hs210 3 ways wiring help
3419 0
Need help with HS210 wiring
679 0
HS210 wiring issue (with diagram!)
5110 1
HS210 Local Only
1439 0
HS 210 wiring question
60 0
Using an HS210 Kit to Replace GE Bluetooth Switches
589 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.