Smart Home Community > All Threads > HS210 Keeps resetting to factory default
< All Threads

HS210 Keeps resetting to factory default

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

HS210 Keeps resetting to factory default

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
HS210 Keeps resetting to factory default
HS210 Keeps resetting to factory default
2021-12-09 23:57:10 - last edited 2021-12-28 05:51:51
Model: HS210  
Hardware Version: V2
Firmware Version: 1.1.5

Hi all

 

I have quite a few (over 20) Kasa smart switches in my house, a combination of HS200, HS210 and HS220. All but one of them works great.

 

One of the HS210 switches has been working great for a couple of months, and then I noticed it had been factory reset. I didn't know why, but I was able to go through the install process again to reconnect it to the network and it seemed to be working fine again. However, within a short period of time it had reset itself again. Other than physically pulling it from the wall I've tried everything I can think of to get it working again (including a manual factory reset), but nothing works.

 

It doesn't even work manually now to switch on the lights. It's blinking orange and green, and if I switch on the lights with it they come on, but then it resets itself again within a minute and turns off the lights again.

 

Does anyone have any suggestions for anything else I could try? 

 

Thanks in advance!

 

Jeff

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:HS210 Keeps resetting to factory default-Solution
2021-12-27 17:35:36 - last edited 2021-12-28 05:51:51

Hello @Solla-topee 

 

Thank you for your response.

 

I did end up pulling the HS210 out and replaced it with another. That one works fine so far.

 

It is installed with an ordinary 3-way switch on the other end.

 

I have contacted support and they mentioned I would receive a contact about returning the unit for replacement. It has not happened yet, but I assume the delay is due to the holiday season.

 

Thank you for your time and support.


Best regards

 

Jeff

Recommended Solution
  2  
  2  
#5
Options
5 Reply
Re:HS210 Keeps resetting to factory default
2021-12-16 13:20:06 - last edited 2021-12-16 13:22:33

Hello @JeffL 

Sorry for the late reply, can you share the Mac address & hardware version of that HS210 to us via private message?

Can you help describe how you notice the switch is factory reset? Did you try to press the ' Reset button' for 10 secs to factory it? 

Do you have HS210 with the same hardware version work fine in the same network? Can I know the model of router, thank you

 

>>Landscape Mode - Tapo App for Pad. >>Smart Action 2.0 Explore and meet the next level home automation. >>How to position my TP-Link camera for optimal performance.
  0  
  0  
#2
Options
Re:HS210 Keeps resetting to factory default
2021-12-17 16:39:54

Thank you for your response @Solla-topee

 

I have messaged you directly with the details.

 

Best regards

 

Jeff

  0  
  0  
#3
Options
Re:HS210 Keeps resetting to factory default
2021-12-22 10:00:35 - last edited 2021-12-22 10:08:32

Hello @JeffL 

Thank you for providing the case details in pm.

I did not notice that even manually HS210 can't turn on the light, if so, please pull the switch out of wall box and checking the wiring of HS210 first.  

 

1. Ensure the wires are still properly connected, not getting loose (cut off breaker and test with a voltage tester before tug the wires)

Here is a set-up video to examine the wiring of HS210:
https://www.tp-link.com/support/download/hs210-kit/

 

2. If you have more HS210 , try to replace the problematic HS210.

May I know how about the LED on 2 * HS210, WiFi led and White Circle. Do you use them as a KIT or with an ordinary 3 way switch?

 

If you ensure the wires are properly connected, and manually smart switch still can not turn on the light, as the switch has been working fine for a few months, it could be a faulty unit,  I recommend to contact retailer or local support to get it replaced under warranty.

>>Landscape Mode - Tapo App for Pad. >>Smart Action 2.0 Explore and meet the next level home automation. >>How to position my TP-Link camera for optimal performance.
  0  
  0  
#4
Options
Re:HS210 Keeps resetting to factory default-Solution
2021-12-27 17:35:36 - last edited 2021-12-28 05:51:51

Hello @Solla-topee 

 

Thank you for your response.

 

I did end up pulling the HS210 out and replaced it with another. That one works fine so far.

 

It is installed with an ordinary 3-way switch on the other end.

 

I have contacted support and they mentioned I would receive a contact about returning the unit for replacement. It has not happened yet, but I assume the delay is due to the holiday season.

 

Thank you for your time and support.


Best regards

 

Jeff

Recommended Solution
  2  
  2  
#5
Options
Re:HS210 Keeps resetting to factory default
2021-12-28 05:51:40

Hello @JeffL 

Thank you sharing and updating here and let us know!

Hope everything goes well while get this unit replaced.

Merry Christmas!

>>Landscape Mode - Tapo App for Pad. >>Smart Action 2.0 Explore and meet the next level home automation. >>How to position my TP-Link camera for optimal performance.
  0  
  0  
#6
Options

Information

Helpful: 0

Views: 1013

Replies: 5

Related Articles
HS210 Local Only
1434 0
Bulb keeps factory resetting after it's been switch off
1876 1
HS210 and HS200 both flashing
405 0
Hs210 3 ways wiring help
3409 0
HS210 Installation
386 0
HS210 Flashing On and Off
1415 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.