Wi-Fi Routers Forums - Home Network Community

How do i fix wifi has self-assigned IP address error on Mac

If your MacBook is displaying the error message and cannot connect to the internet One of the reasons for this error message to appear on your MacBook is that your “WiFi has self-assigned IP address.

Firmware UpdateFeature RequestAccess Point ModeAccess Control

By macapple · Latest post 2024-03-31 00:07:35 by ArcherC8

0Helpful

99Views

1Replies

Can't take ownership of router - router is BOUND to prior owner

Very frustrating. Even when you do a full factory reset... the tether/phone app has MORE options than the web admin page and I discovered that the router is bound to the prior owner. I cannot reset th

Feature RequestAccess ControlBINDING to tp-link account

By Username1401 · Latest post 2024-03-22 17:12:52 by Riley_S

0Helpful

85Views

1Replies

Feature Request: Tailscale VPN Support

Please add Tailscale VPN support on all high-end Wi-Fi 6/6E/7 routers (e.g., from AX6000 to BE900).

Feature RequestFirmware UpdateVPNTailscale

By JamesAndersonJr · Latest post 2024-03-20 13:05:34 by NightDarkness

9Helpful

310Views

1Replies

Archer AX50 will not le me Upload more than 50MB

Archer AX50, Googlefiber 1g up 1g down, Upload speed wont go over 30mb. Already disconnected and reboot, duplex is at full 1000mb, QoS has been set to 999MB UL and 999MB DL, removed home security, con

Bandwidth Control/QoSFeature RequestPort ForwardingAccess Controlupload speed

By Hero_Cardenas

0Helpful

42Views

0Replies

Be19000 can not change channel width

I want to change the channel width to on the 5ghz channel to 160 wide, I have disabled smart connect and disabled one mesh. I only have a choice for the router to choose the width.

Feature Request

By Kobigu · Latest post 2024-03-04 11:52:29 by Sunshine

0Helpful

131Views

1Replies

negotiated ethernet speed status

Hi there. Can you please fix empty dash for for Tx/Rx rate for ethernet clients in Network Map>Clients web management page? It shows speeds and signal strenght approximations for Wi-Fi clients but no

Feature Request

By Rch11 · Latest post 2024-02-27 03:34:56 by Rch11

0Helpful

97Views

2Replies

Need to know how to enable ICMP requests from tunnel broker service to Archer AX1800 Home router

hello i need to know how do i enable ICMP requests on my router because i signed up for a temporary tunnel service and the tunnel broker service is netassist and i dont have the option to do manual 6t

IPv6Feature Request

By IPv6person

0Helpful

127Views

0Replies

add name to client device

How can I add/modify the name of a device listed under client devices?

Feature Request

By Georgia_Girl · Latest post 2024-02-13 00:31:30 by terziyski

0Helpful

114Views

1Replies

Stop redirecting local IP to tplinkwifi.net

My gateway is 10.0.0.1, when I visit it to make any changes most of the time I get redirected to tplinkwifi.net. I have DNS over TLS and DNS over HTTPS on all of my devices. So tplinkwifi.net will not

OneMeshEasyMeshFeature RequestFirmware Update

By Archer3150 · Latest post 2024-02-09 19:12:56 by effem

8Helpful

571Views

3Replies

TP-Link AX1800 DOH support ?

I just bought TP-Link AX1800, and disappointed to find that there is no option for DOH (DNS over HTTPs) in 2024. I also found the following thread: https://community.tp-link.com/en/home/forum/topic/61

Feature Request

By tpuserax1800

0Helpful

73Views

0Replies