Home Network Community > Wi-Fi Routers > Archer C7 V2 Unable to get IPV6 working
< Wi-Fi Routers

Archer C7 V2 Unable to get IPV6 working

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer C7 V2 Unable to get IPV6 working

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Archer C7 V2 Unable to get IPV6 working
Archer C7 V2 Unable to get IPV6 working
2020-03-08 21:00:17 - last edited 2020-03-09 01:08:48
Model: Archer C7  
Hardware Version: V2
Firmware Version: 3.15.3 Build 180114 Rel.39265n

I have service with Xfinity in San Jose, CA. I am using a D-link DCM301 cable modem connected to my Archer C7 V2. I am unable to get IPV6 working with this setup. When i connect my Windows PC directly to the DCM301, i can get external IPV6 connectivity (https://test-ipv6.com/). When i reconnect my archer c7 and power cycle everything, i do not have IPV6 connectivity. I have enabled IPV6 in the router. 

 

On WAN Settings:

1. Set WAN Connection type to DHCPv6

2. Choose "Get IPV6 prefix delegation"

3.  Get IPV6 DNS server automatically

 

On LAN Settings:

1. On IP address assign type: "DHCPV6 server"

 

Does anyone have a working IPV6/Cable modem setup with this router ?

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Archer C7 V2 Unable to get IPV6 working-Solution
2020-03-08 22:54:43 - last edited 2020-03-09 01:08:48
That is the same WAN IPv6 settings I have on my Archer C8 and I use Xfinity in the Orlando area. I get an IPv6 connection. On my LAN IPv6 setting which are grayed out I have assign type as SLAAC and address prefix as two : as it seems like when I set it up I have to set that also. After making your changes, power cycle the router and then see if you have IPv6.
Recommended Solution
  1  
  1  
#2
Options
2 Reply
Re:Archer C7 V2 Unable to get IPV6 working-Solution
2020-03-08 22:54:43 - last edited 2020-03-09 01:08:48
That is the same WAN IPv6 settings I have on my Archer C8 and I use Xfinity in the Orlando area. I get an IPv6 connection. On my LAN IPv6 setting which are grayed out I have assign type as SLAAC and address prefix as two : as it seems like when I set it up I have to set that also. After making your changes, power cycle the router and then see if you have IPv6.
Recommended Solution
  1  
  1  
#2
Options
Re:Archer C7 V2 Unable to get IPV6 working
2020-03-09 01:10:07 - last edited 2020-03-09 01:12:00

@ArcherC8 Thank you for your sugegstion. I tried switching "IPV6 Address assign type" To SLAAC and that got ipv6 working on my PC. Also confirmed with Ping and tracert on external sites using IPV6

  0  
  0  
#3
Options

Information

Helpful: 0

Views: 2613

Replies: 2

Related Articles
Archer AX1500 IPv6 Not Working?
1413 0
 Archer C7 v2 OpenVPN Client
922 0
 Update Archer C7 V2 to V5?
5046 0
 Archer C7 v2 and Spectrum Internet
557 0
 Archer C7 (v2) slow wired speed
1083 0
 Upgrading my Archer C7 AC1750 router v2
1245 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.