Home Network Community > Wi-Fi Routers > AX6000 stops allowing connections
< Wi-Fi Routers

AX6000 stops allowing connections

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

AX6000 stops allowing connections

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
AX6000 stops allowing connections
AX6000 stops allowing connections
2021-11-09 19:49:19 - last edited 2021-11-09 19:51:54
Model: Archer AX6000  
Hardware Version: V1
Firmware Version: 1.2.3 build 20210511

My AX6000 has started to not allow new connections via WiFi unless rebooted. The problem is this is not consistent. It will operate just fine for up to a week at a time, then starts to randomly deny connections from devices that were already connected before. At that point I need to power-cycle. Is there an upper limit on connected devices? My previous router needed to be rebooted.. well.. never, so I do consider this to be unacceptable behaviour. To clarify - by denying connection I mean using WPA2 personal with a valid password I get told "unable to connect".

  0      
 
  0      
 
#1
Options
9 Reply
Re:AX6000 stops allowing connections
2021-11-10 07:36:02

@ffr2822 

 

Hello, does this "unable to connect" error occur on some special or specific devices? Or does it randomly happen on all the wireless client devices? Please try to modify the wireless settings on the AX6000 as follows:

 

Do the same for both the 2.4G and 5G wireless network, then reboot the router to monitor.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:AX6000 stops allowing connections
2021-11-27 19:20:37

@Kevin_Z Been there, done that. It was random - ESP8622 based devices, iPhone, iPad, Mac Book, apple watch, HP printer. I gave up on smart connect almost immediately. I suspect the fact that I can "see" 17 SSIDs on m macbook is part of the issue. Things have been a bit more stable since I did a firmware update.

 

  0  
  0  
#3
Options
Re:AX6000 stops allowing connections
2021-11-29 09:21:40

@ffr2822 

 

Got it. Please monitor the wireless connection for some time, then report back on how this is going. BTW, please show me what is the firmware version of the Archer AX6000 if the issue persists.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#4
Options
Re:AX6000 stops allowing connections
2021-12-14 19:00:57
I'm running the current beta, and still having the problem (Was given the beta to test HFS+ issues)
  0  
  0  
#5
Options
Re:AX6000 stops allowing connections
2021-12-17 08:12:04

@ffr2822 

 

Can I have the detailed version of the beta firmware you are running on the AX6000?

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#6
Options
Re:AX6000 stops allowing connections
2021-12-22 15:41:31

@Kevin_Z See image - it's a screen capture.

9b8dbee67cf44c64a69408db90e7cda9

 

  0  
  0  
#7
Options
Re:AX6000 stops allowing connections
2021-12-23 07:18:33

@ffr2822 

 

I found you were discussing the HFS+ issue with the support engineers and was provided the beta firmware, I would suggest you discuss the disconnect issue with him again to check if he has further suggestions.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#8
Options
Re:AX6000 stops allowing connections
2021-12-26 20:08:21

@Kevin_Z I was just giving an update after you asked - the connection dropping is random both in time and amount, so it will be very difficult to debug - especially remotely. The other issue has been resolved (I just checked the drive after a needed reboot and it is no longer scrambling the formatting) - I've given engineering my solution.

  0  
  0  
#9
Options
Re:AX6000 stops allowing connections
2021-12-27 01:57:50

@ffr2822 

 

That sounds good. Let's wait and see if the engineering team has any suggestions on that.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#10
Options

Information

Helpful: 0

Views: 1176

Replies: 9

Related Articles
 AX 6000 - Wireless 2.4Mhz and 5Mhz router stops allowing traffic between the two.
583 0
 Archer AX6000 not allowing full Enterprise Aruba connection
464 0
 AX6000 router does not work with wired connections
1084 0
 Archer C3200 not allowing incoming connections.
1698 0
 Router not allowing incoming connections from the Internet
125 0
AX6000 5GHz Dropping
536 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.