Home Network Community > Deco > 40mhz wide 2.4ghz channels not using 1,6, or 11
< Deco

40mhz wide 2.4ghz channels not using 1,6, or 11

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

40mhz wide 2.4ghz channels not using 1,6, or 11

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
40mhz wide 2.4ghz channels not using 1,6, or 11
40mhz wide 2.4ghz channels not using 1,6, or 11
2022-08-09 19:48:52
Model: Deco XE5300  
Hardware Version:
Firmware Version: 1.1.5 Build 20220429

Hello,

 

Is there a way to assign channel with the XE5300?  2.4ghz auto set its self to 40mhz wide on channel 9. This is not a best practive or recomended and it causing adjacent channel interference from my neighbors and i am not being a good wireless steward by not using one of the 3 non overlapping channel 1,6, or 11

 

Thanks,

 

Chris

  0      
 
  0      
 
#1
Options
3 Reply
Re:40mhz wide 2.4ghz channels not using 1,6, or 11
2022-08-09 22:31:15 - last edited 2022-08-09 22:32:29

  @Chris_Couch,

Our Deco Systems do not currently let the user actively select which channel the network uses to communicate. The nodes will optimize based on the networks that are visible in the area. To force the system to scan for new channels and determine the best connection. You can find the optimize now button in your Deco App to begin the process. Keep in mind that there are many variables and sources of interference that may cause the Deco to select a specific channel, even if it appears empty to you.

 

I was able to find this post on the global forums detailing why this can be difficult for mesh networks. https://community.tp-link.com/en/home/forum/topic/154561

Check out the Latest: Getting Started with EasyMesh and TP-Link New Tablet Mode for the Tapo App Comparing the Latest Tapo Doorbells
  0  
  0  
#2
Options
Re:40mhz wide 2.4ghz channels not using 1,6, or 11
2022-08-11 13:16:37

  @Riley_S 

Thank you for the link and explaination, I can understand not letting the user select channels for back haul but per the app all back haul is going over 6ghz not 2.4 or 5ghz so channel selection in the other bands shouldnt affect that.  The part i am really having trouble with and dont understand is that the basic deployment model for all 2.4ghz channels is to use 1,6,11(US based) and at 20mhz. This device goes against everything out there. I have a spectrum analysis tools at my home as part of my work. I can see the spectrum and current channel plan.

  1  
  1  
#3
Options
Re:40mhz wide 2.4ghz channels not using 1,6, or 11
2022-11-07 19:02:15

  @Chris_Couch 

 

I totally agree with you. I cannot understand why TP-Link has determined not to permit the end-user to set the 2.4 GHz channel, as well as channel width.

  0  
  0  
#4
Options

Information

Helpful: 0

Views: 570

Replies: 3

Related Articles
Archer a7 2.4 ghz channels 7 through 11 not showing up
705 0
XE5300 seperate channels while connected to ethernet
426 0
2.4ghz Channel
566 2
RE450 and Windows 11
967 0
Some nodes using different wifi channels and band width
778 1
Channels
301 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.