Home Network Community > All Threads > Connecting to ADSL directly with Deco M5 ??
< All Threads

Connecting to ADSL directly with Deco M5 ??

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Connecting to ADSL directly with Deco M5 ??

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Connecting to ADSL directly with Deco M5 ??
Connecting to ADSL directly with Deco M5 ??
2020-04-16 15:20:43 - last edited 2020-04-16 15:30:10
Model: Deco M5  
Hardware Version: V1
Firmware Version:

Hello

 

I am researching my option to purchase https://www.amazon.com/TP-Link-Deco-Whole-Home-System/dp/B06WVCB862

However, My current setup at home is using this Sagemcom router: 

Board ID: F@ST2704N
HardWare Version: SG_NGR_2704N.1.1 

 

which is connected to internet using ADSL.

 

I read this point 

 

4. In AP mode, since all the clients are managed by the root router, some advanced features will not be available in the Deco app, including Antivirus, Parental Controls, Port Forwarding, Address Reservation, TP-Link DDNS, etc.

 

My main motive is to use the Parental Controls feature. So, does this mean that I will have to connect to internet using Deco M5 directly instead of using the Sagemcom home router?? Would Deco M5 connect to internet using ADSL??

 

Thanks in advance.

 

 

 

  0      
 
  0      
 
#1
Options
3 Reply
Re:Connecting to ADSL directly with Deco M5 ??
2020-04-16 17:01:48

@samir_sabri 

 

You can setup the Deco WAN settings to be a PPPoE authenticator, meaning you can set your ADSL PPPoE username and password on the Deco for it to get the IP address and thus use the rotuer in routed mode to get access to all of its features.  It cannot however replace the modem.  If your sagecom is a dual purpose gateway (modem and router) you would want to put it in bridged mode.  This disables the router features of the sagecome but keeps the modem feature active.

 

 

 

Check out the Latest: Recent Smart Home Features and Updates for Tapo and Kasa Securing Your TP-Link ID with 2FA:Deco and Tether | Smart Home Splash into a Smarter Summer with Sub-G Sensors, Matter, and Apple Home!
  0  
  0  
#2
Options
Re:Connecting to ADSL directly with Deco M5 ??
2020-04-17 06:34:02 - last edited 2020-04-17 11:11:30

@Carl Thanks for your reply. My sagecom is a dual purpose gateway, as its described as an ADSL ROUTER at their manual.

 I've checked their manual, I am not sure if I can set it as bridge mode. 

 

Suppose if I set it as bridge mode, would I be able to use all advanced features of Deco M5? ex: Parental Control. Would I still have to connect Deco to it ?

 

Also, what modem do you advice if I could not set my sagecom to bridge mode? 

 

 

  0  
  0  
#3
Options
Re:Connecting to ADSL directly with Deco M5 ??
2020-04-17 19:03:55

@samir_sabri 

 

 

Yes if the device can be put in modem only or bridge mode then the Deco can be used in routed mode and you will have access to all of its features.  We haven't sold ADSL products in the US in quite some time.  But for a modem i would recommend any ADSL2+ modem that is just a modem.  If you can find one with a 10/100/1000 port even better. 

Check out the Latest: Recent Smart Home Features and Updates for Tapo and Kasa Securing Your TP-Link ID with 2FA:Deco and Tether | Smart Home Splash into a Smarter Summer with Sub-G Sensors, Matter, and Apple Home!
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 2041

Replies: 3

Related Articles
Connecting Deco App to Deco m5 that has already been set up
10274 0
No internet when connecting directly to deco
612 1
Connecting deco m5 by cable
1067 0
Connecting Xbox to Deco M5 wired?
2063 0
Ford Sync 3 not connecting to Deco m5
84 0
Connecting two X60 nodes directly to modem?
804 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.