Home Network Community > All Threads > Router only reconizes 10mbps LAN
< All Threads

Router only reconizes 10mbps LAN

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Router only reconizes 10mbps LAN

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Router only reconizes 10mbps LAN
Router only reconizes 10mbps LAN
2023-02-22 21:52:01
Tags: #Access Point Mode #Access Control
Model: Archer AX1800  
Hardware Version:
Firmware Version:

It's a bit of a setup here.  We have Starlink>CPE210 AP>CPE210 Client>AX1800 Router

 

The router only recognizes the Client 210 as 10 Mbps.  If I plug directly into the Client 210, I get full speed.  Using the router, I only get 10 Mbps. 

 

 

I tried changing the internet port negations speed settings but would just lose connection.

 

 

 

 

I'm learning as I go, any help would be appreciated.  


Thanks in advance

  0      
 
  0      
 
#1
Options
4 Reply
Re:Router only reconizes 10mbps LAN
2023-02-23 15:13:50 - last edited 2023-02-24 09:59:19

  @twowaysplit 

 

Have you tried to use a different ethernet cable ? Sometimes a working cable can cause this behavior. Try with another one of a good quality (Cat 5e/6).

In rare cases this can be caused by a faulty ethernet port on the device. Here's a troubleshooting guide for this type of issue.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  2  
  2  
#2
Options
Re:Router only reconizes 10mbps LAN
2023-02-24 00:45:24
So this morning I had it working.  It was correctly labeled as 100mbps Full Duplex.  Speeds where fine for a couple of hours and now it has switch back the 10mbps. I've tried a couple of cables as well.  
  0  
  0  
#3
Options
Re:Router only reconizes 10mbps LAN
2023-02-24 09:37:43

@twowaysplit 

 

Hi, 

 

I'm wondering if there is a possibility to test and confirm whether you can get 100Mbps or 1000Mbps negotiation when connecting the AX1800 directly to the Starlink.

 

If they can negotiate at a correct speed, then I may say the distance or the cable between the CPE210 client and the AX1800 may be the cause of the issue. You need to try with a shorter cable or one with a better quality.

If my reply helps with the issue, please click on the arrow pointing upward. If it solves your issue, please click the star to mark it as a "Recommended Solution".
  1  
  1  
#4
Options
Re:Router only reconizes 10mbps LAN
2023-02-25 20:26:21
So, I forgot to mention that if I plug directly into the Client CPE210 (at the point it plugs into the router), I get full speeds. Also, the cable length max is 200ft Cat6. From the router to my pc is a 50ft (assuming) Cat6 and there aren't any sharp corners, kinks, etc. throughout all lines.
  0  
  0  
#5
Options

Information

Helpful: 0

Views: 1223

Replies: 4

Tags

Access Point Mode Access Control
Related Articles
DSL to AX1800 Router - LAN Ports not connecting
993 0
Download speed capped at 10Mbps
815 0
Lan from router or switch
448 0
Archer A7 wan port only 10mbps
1054 0
Router and router as access point
1200 0
How to enable LAN ping on AX1800?
898 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.