Home Network Community > Wi-Fi Routers > Archer A7, Access Point mode, custom beacon interval
< Wi-Fi Routers

Archer A7, Access Point mode, custom beacon interval

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer A7, Access Point mode, custom beacon interval

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Archer A7, Access Point mode, custom beacon interval
Archer A7, Access Point mode, custom beacon interval
2022-01-09 20:09:38 - last edited 2022-01-12 16:51:44
Model: Archer A7  
Hardware Version:
Firmware Version:

After switching to access point mode, it looks like the advanced "system parameters" UI section is gone. That contained some knobs that seem applicable to access point mode as well as router mode, such as custom beacon interval. Would love to hear of some work-around to get this back, short of installing OpenWRT.

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Archer A7, Access Point mode, custom beacon interval-Solution
2022-01-12 16:34:38 - last edited 2022-01-12 16:51:44

@JKNetwork 

 

So the enigneers got back to me and let me know only specific products on an SPF platform will support the system parameters in AP mode.  They did say that a work around would be to set the features in Router mode and then switch to AP mode.  The settings will be maintained.  

Recommended Solution
  0  
  0  
#4
Options
4 Reply
Re:Archer A7, Access Point mode, custom beacon interval
2022-01-11 01:09:18

@JKNetwork 

 

I checked with the QA team and that section should still be there, even in AP mode.  If you can please let me know what Firmware you are using and a screenshot that the menu is gone.  I will need them to test.

  0  
  0  
#2
Options
Re:Archer A7, Access Point mode, custom beacon interval
2022-01-11 14:10:38

@Carl thanks for looking into this!

 

Firmware Version:
1.1.4 Build 20211022 rel.58866(5553)
Hardware Version:
Archer A7 v5.0

 

Here it is running in AP mode, showing the System Tools menu from the left. When running in router mode, there's a "System Parameters" sub-menu (all of this only visible when on the Advanced tab at the top of the page; notably the Basic and Advanced tabs are missing here).

 

81f1eef2f7b641308f0449cb06bc0261

  0  
  0  
#3
Options
Re:Archer A7, Access Point mode, custom beacon interval-Solution
2022-01-12 16:34:38 - last edited 2022-01-12 16:51:44

@JKNetwork 

 

So the enigneers got back to me and let me know only specific products on an SPF platform will support the system parameters in AP mode.  They did say that a work around would be to set the features in Router mode and then switch to AP mode.  The settings will be maintained.  

Recommended Solution
  0  
  0  
#4
Options
Re:Archer A7, Access Point mode, custom beacon interval
2022-01-12 16:51:34

@Carl thanks again for following up. It's good to know that the settings will be maintained, as it's not easy to verify these particular ones.

  2  
  2  
#5
Options

Information

Helpful: 0

Views: 718

Replies: 4

Related Articles
Archer A7 as access point - devices can't reach internet
912 0
A7 Access Point mode questions
350 0
Deco X20 Access Point Mode Questions
1608 0
Guest network for Archer a7 while in Access Point mode
511 0
TP-Link Cloud option not available when in Access Point mode?
402 0
Archer A7 Access Mode - Disable WPS
1152 0
About Us
Press
Copyright © TP-Link USA Corporation. All rights reserved.