Home Network Community > Deco > Deco M4 - speed capped at 100Mbps
< Deco

Deco M4 - speed capped at 100Mbps

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
123...

Deco M4 - speed capped at 100Mbps

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Deco M4 - speed capped at 100Mbps
Deco M4 - speed capped at 100Mbps
2020-02-26 08:03:21 - last edited 2020-03-19 08:39:47
Model: Deco M4  
Hardware Version: V1
Firmware Version: 1.1.0 Build 20190620 Rel. 45372

Hi

 

I've been using Deco M4 since 5 months.

The setup was:

Broadband modem ==> Deco M4 1st unit ==> Deco M4 2nd unit.

 

Earlier my broadband was only 100Mbps and later I've upgraded it to 200Mbps.

My broadband modem and Deco M4 1st unit is connected using a Cat 6 ethernet cable. But still the maximum speed I'm receiving is capped at 100Mbps via Deco.

 

When I directly connect to my broadband modem then I'm receiving speeds upto 200Mbps.

Followed the troubleshooting steps on Deco but it didn't help!

 

Thanks

  0      
 
  0      
 
#1
Options
2 Accepted Solutions
Re:Deco M4 - speed capped at 100Mbps-Solution
2020-03-18 06:41:54 - last edited 2020-03-19 08:39:47

@Himanshu_IN the QoS in the Deco app was set at 100Mbps. Increasing that to 1000Mbps helped fix the issue.

Recommended Solution
  41  
  41  
#6
Options
Re:Deco M4 - speed capped at 100Mbps-Solution
2022-02-21 05:54:20 - last edited 2022-02-21 05:54:26

  @George.Bran 

Thank you very much for the feedback.

We are trying to collect more similar cases and complete the troubleshooting steps.

It is only suggested to have a look at this link and comment below:

Deco LAN speed is capped to 100m/s

Deco Monthly Recap- Check What's Currently Going on With Deco KidShield Test Recruitment, Share Your Ideas With us! Wi-Fi Schedule Ideas Wanted!
Recommended Solution
  0  
  0  
#44
Options
56 Reply
Re:Deco M4 - speed capped at 100Mbps
2020-02-27 01:22:34

@PavanKumar 

 

Hello, may I know what kind of troubleshooting you have done already? Below we list some information we need to narrow down this issue and fix it.

 

1. With a computer connected to the main Deco by wired cable directly, what is the speed you can get from it? Please check the wireless speed you can get from the main Deco as well with slave Deco powered off. 

2. At the same, please check the wired/wireless negotiation speed of your device. You can refer to https://www.tp-link.com/support/faq/2265/

3. What is the current operation mode of your Deco M4? 

4. Try to swap the locations of the Decos or switch the slave Deco to main Deco to give it a shot. Below is the instruction:

https://www.tp-link.com/support/faq/2400/ 

 

Good day. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:Deco M4 - speed capped at 100Mbps
2020-02-27 17:02:59

@Kevin_Z 

 

1. With a computer connected to the main Deco by wired cable directly, what is the speed you can get from it? Please check the wireless speed you can get from the main Deco as well with slave Deco powered off. 

Wired to main deco - 100 Mbps

Wireless to main deco with slave powered off - 100 Mbps

 

2. At the same, please check the wired/wireless negotiation speed of your device. You can refer to https://www.tp-link.com/support/faq/2265/

Please find attached the screenshots of the Ethernet and Wifi speed which is 1Gbps and 433.3Mbps respectively.

 

3. What is the current operation mode of your Deco M4? 

Dynamic IP

 

4. Try to swap the locations of the Decos or switch the slave Deco to main Deco to give it a shot. Below is the instruction:

https://www.tp-link.com/support/faq/2400/ 

Swapped the main deco with slave deco and repeated step 1 to test the speeds. It's still the same with maximum at 100Mbps.

File:
link speed 1.jpgDownload
  0  
  0  
#3
Options
Re:Deco M4 - speed capped at 100Mbps
2020-02-28 12:27:56

@PavanKumar 

 

Thanks for your valued reply. Cause the speed gets stuck at 100Mbps and cannot be fixed via the troubleshooting methods we have done. 

 

To help you figure it out, our engineer will email you later and try to do further analysis to find a solution.

 

Please check your inbox and get in touch with our engineer. 

 

Good day. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#4
Options
Re:Deco M4 - speed capped at 100Mbps
2020-03-18 05:52:07

@PavanKumar  were you able to fix the issue?

  0  
  0  
#5
Options
Re:Deco M4 - speed capped at 100Mbps-Solution
2020-03-18 06:41:54 - last edited 2020-03-19 08:39:47

@Himanshu_IN the QoS in the Deco app was set at 100Mbps. Increasing that to 1000Mbps helped fix the issue.

Recommended Solution
  41  
  41  
#6
Options
Re:Deco M4 - speed capped at 100Mbps
2020-09-23 21:44:39

@PavanKumar I found that turning off the second deco(pulling the plug) for 5 minutes works... Now I get more than 100 mbps

  1  
  1  
#7
Options
Re:Deco M4 - speed capped at 100Mbps
2020-11-27 06:07:25
Pavan , i was going bat crazy, never crossed my mind to check QoS, apparently if you set a device with high priority the Deco sets itself to 100 Mb.
  1  
  1  
#8
Options
Re:Deco M4 - speed capped at 100Mbps
2020-11-27 06:33:21

 

Florin84 wrote

Pavan , i was going bat crazy, never crossed my mind to check QoS, apparently if you set a device with high priority the Deco sets itself to 100 Mb.

@Florin84 still capped at 100

  0  
  0  
#9
Options
Re:Deco M4 - speed capped at 100Mbps
2020-11-27 07:12:19

@Florin84 Main deco rebooted after disconnecting the other 2 slaves, wifi speeds returned to normal 400 Mb (QoS) was enabled on 2 devices before, i deleted them ).i reconnected the slaves i get the usual 79- 90 fluctuating wifi speeds (the slaves are connected wirelessly not cabled). It seams the QoS somehow was stuck on all slaves (i fell the option propagates from the main to slaves and only fixed by disconnecting all slaves and rebooting main). 

  0  
  0  
#10
Options
Re:Deco M4 - speed capped at 100Mbps
2020-11-27 20:01:06

@PavanKumar i have this exact issue , thought it was odd my pc ran faster download speeds on wireless than wired. I have set me qos to 1000 down and 1000up and it still is capped at 100mbps wired to my pc. i also tried this with my pc set to high priority and also not high priority and neither worked.

  6  
  6  
#11
Options
123...

Information

Helpful: 0

Views: 54647

Replies: 56

Related Articles
My Deco M4 capped at 100MBPS only
188 0
 Deco M4 capped at 100mbps
2367 3
 Deco M4 - speed capped at 100Mbps
1790 0
Deco m4 Ethernet and wireless capped at 100 Mbps
26010 0
Internet speed capped at 100mbps
2102 0
Speed Capped to 100mbps in Archer C50
2749 1
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.