Home Network Community > DSL Modem&Routers > Bug in Service Filtering for VR600 Beta Firmware
< DSL Modem&Routers

Bug in Service Filtering for VR600 Beta Firmware

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Bug in Service Filtering for VR600 Beta Firmware

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Bug in Service Filtering for VR600 Beta Firmware
Bug in Service Filtering for VR600 Beta Firmware
2020-09-09 15:35:39
Model: Archer VR600  
Hardware Version: V2
Firmware Version: 0.4.0 0.9.1 v0074.0 Build 200701 Beta.71362n

I've found another bug in the latest firmware for the VR600.

 

I tried to set up Service Filtering to block DNS traffic from certain clients.

 

I fill in as follows:

When I click Save I get an error message:

However, it has actually saved with IP address undefined.

 

When I try to delete the item I get another error message:

 

Frustrating.

 

This is with firmware 0.4.0 0.9.1 v0074.0 Build 200701 Beta.71362n which isn't labelled as a Beta on the download site so you only find out after installing it.

  1      
 
  1      
 
#1
Options
5 Reply
Re:Bug in Service Filtering for VR600 Beta Firmware
2020-09-10 06:39:05

@dunxd 

Good day.

Sorry for the delay.

Even though there would be an error message pop out, the service filtering rule actually saved but for unknown IP addresses?

When you tried to delete it, have you tried to turn off the service filtering and try to delete it again?

 

Did the issue start after you updated the latest beta firmware？

And have you tried to reset the modem and configure the service filtering again to see what happened?

Thank you very much!

TP-Link Annual Community Survey | Help Shape Our Community Throughout 2024!
  0  
  0  
#2
Options
Re:Bug in Service Filtering for VR600 Beta Firmware
2020-09-10 09:36:32

@Sunshine That is correct, even after getting the error message the rule saved with undefined IP addresses (at least that is what the web interface shows).

 

I am unable to modify or delete the rule. This is the case with Service Filtering switched on or off.

 

I tried to set up the rule after upgrading to the latest firmware, which I didn't realise was beta until after installing it. I don't know if this issue existed with previous firmware.

 

I have not tried resetting the modem yet as this will be quite disruptive, as I don't have a backup of all settings prior to making this change. I am leaving Service Filtering disabled for now. Hoping for some production grade firmware, clearly labelled on the support site, soon.

  0  
  0  
#3
Options
Re:Bug in Service Filtering for VR600 Beta Firmware
2020-09-10 17:23:33

+1

Hoping for production grade firmware for the VR series modem/routers too, rather than "Beta"

  0  
  0  
#4
Options
Re:Bug in Service Filtering for VR600 Beta Firmware
2021-09-24 01:57:30

@Sunshine 

 

I have reported exactally the same issue on my VR1600v tplink router.

Here: https://community.tp-link.com/en/home/forum/topic/256050

 

Here is my tp-link router firmware version.  

Current Firmware Version:0.1.0 0.9.1 v5006.0

Build 200810

Rel.53181n 

Hardware Version:Archer VR1600v v2 00000000

 

It's also been reported here:

https://community.tpg.com.au/t5/Modems-and-Devices/Archer-VR1600V-firmware-update/td-p/74893

  2  
  2  
#5
Options
Re:Bug in Service Filtering for VR600 Beta Firmware
2021-09-24 09:36:03

@tpgNbn50 Hi, nice to see you again, and please refer to the suggestions in the other post.

Deco Monthly Recap- Check What's Currently Going on With Deco
  0  
  0  
#6
Options

Information

Helpful: 1

Views: 1521

Replies: 5

About Us
Press
Copyright © TP-Link Corporation Limited. All rights reserved.