Solution Powerline Extender Acting as the DHCP server
This Article Applies to:
TL-WPA7510, TL-WPA9610, TL-WPA8730/8630(P) V2, WPA4220 V3, etc.
Problem Description/ Phenomenon:
What is Smart DHCP, and How does Smart DHCP work? Visit TP-Link Smart DHCP Makes Network Configuration Simple.
Some users may find that after the power outage or router’s rebooting, even after router’s internet is back and up running, client devices still get IP address from powerline extender, and cannot connect to the internet.
Note: if router loses internet and then goes back afterwards, powerline extender will do a scan automatically, if it detects another DHCP Server is running, it will disable its own automatically (when powerline units remain paired), and the devices will get IP address from main router then access the internet through that.
Troubleshooting Suggestions:
1. Double check if the main router’s internet is actually back ON and working fine.
To confirm this, wire a computer or laptop to another LAN port of the router using an Ethernet cable, leave the main powerline adapter connected to the LAN port of the router as well, check if you can access the internet successfully on the computer or laptop. If yes, that means the router's DHCP server is up and running; If not, you will need to check what's wrong with the router after the reboot or power outage.
2. Make sure the powerline adapter and extender are still paired (house LEDs are ON), show us the IP address on the clients devices. Compare that when the internet is good and when it is not.
How to check the IP address on a computer: https://www.tp-link.com/support/faq/669/.
If your model is not listed or the issue persists, please report back with the information below to help locate the issue.
Or send a support email to TP-Link technical support with title ‘[Forum ID 265692] Powerline Extender Acting as the DHCP server’ to get further assistance:
1. How did you find out powerline device's DHCP server does not work properly? Did you often reboot main router or is there often power outage in your house?
2. Does router’s internet work fine at that moment?
3. LED status on both powerline units.
4. Brand and Model of router, the network topology, for example:
ISP modem --- Router Archer C7 --- PA8010 .... <powerline> ...WPA8630P --- Asus laptop model X.
5. Model & OS of devices that connected to wireless powerline unit.
6. Model number & firmware and hardware version of your powerline KIT, update the firmware if it is not the latest version:
How to update the firmware of the powerline adapter using the tpPLC Utility: https://www.tp-link.com/support/faq/1091/
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
@Solla-topee They've finally added the disable DHCP server option in the latest firmware :)
https://static.tp-link.com/upload/firmware/2022/202204/20220420/TL-WPA8631P(EU)_V3_220330.zip
I hope it works, because the constant disconnects have been killing me..
- Copy Link
- Report Inappropriate Content
Is this firmware available for the 9610? If so can you please direct me to the link? Thank you.
- Copy Link
- Report Inappropriate Content
Hello @BiggySmall thank you for asking, I do not see the beta for TL-WPA9610 right now, I will record your request for further evaluation. If there is any beta or new firmware released, I will update on the page one of this thread.
- Copy Link
- Report Inappropriate Content
@Nor7on Great news, thank you for the sharing!
@Gantolandon @Cecil_ @BobBrown
TL-WPA8631P_V3(EU/UK) official firmware has newly added DHCP server configuration function.
The firmware or latest beta should help with improving stability if the cause is smart DHCP server, feel free to let us if this helps with the situation. If that's not the case, please also start a new thread for unstable concern and provide some case details so we could help look into that further.
Once we support get updated information with firmware release or new beta, we will update on Page one of this thread, go the first page to check if there is any new firmware that you could give it try first, thank you.
- Copy Link
- Report Inappropriate Content
For TL-WPA7517 unstable concern, we created a support email TKID220414822 to look into that further, kindly check your email inbox.
- Copy Link
- Report Inappropriate Content
@Solla-topee I thought I'd check in to see if there was any progress on this very long running issue for the WPA4220 V5
Sadly (but not unexpectedly) there is no progress.
The beta version you promote at the start of this very long thread DOES NOT WORK.
It does NOT disable the DHCP server when you assign a static IP address. You can see in the logs that it still starts up and immediately starts offering DHCP leases to unsuspecting devices on my network. It then shuts down after about 25 seconds when it realises there is another DHCP server available, but if the link from the powerline network to my wider network is broken for more than a few seconds, the DHCP server starts up again?!?!
Why do you say it's fixed when it clearly isn't? What is the matter with your development team?
*Update*
The WPA4220 V5 May 2022 beta on the first page of this thread finally seems to stop the stupid DHCP behaviour
- Copy Link
- Report Inappropriate Content
Sad owner of a TL-WPA4220 here.
Truly amazing just how bad this piece of equipment is compared to all the other TP-Link gear I've owned previously.
What I mean by that is: the piece of equipment works just fine, but there is NEVER an excuse for spawning a rogue DHCP server. Absolutely horrible design, and absolutely horrible response from TP-Link to literal years of problem reports.
Edited to add:
1. I don't have a lot of money, so buying a piece of equipment which is broken in this way negatively impacts me.
2. I live in an area with frequent power outages, and every time one happens, if the device is plugged in, it causes unpredictable impacts to my entire network.
Truly unbelievable this hasn't been fixed once and for all, preferably by ripping the "smart DHCP" feature completely out of the firmware.
- Copy Link
- Report Inappropriate Content
And still no updated firmware for the TL-WPA8630P V2 that switches off the DHCP....
TP Link Support wrote in email saying it would be delivered in March 2022....
Still a pile of unusable cr*p sat in my house waiting for the so called Support team to get their act together.
- Copy Link
- Report Inappropriate Content
@PC_60 @dunxd @Jvmd @Zoltar74@Njd4
Hello everyone,
Some good news and update here, there are some models that officially support DHCP setup , below are some models that newly added DHCP server configuration function.
TL-WPA8630P_V2(EU/UK)
TL-WPA4220_V4 (EU); TL-WPA4220_V4 (UK)
Please go to Page one of this thread or tp-link official website to get the information of new firmware.
The firmware or latest beta should help with improving stability if the cause is smart DHCP server, feel free to let us if this helps with the situation. If that's not the case, please also Start a New thread for unstable concern and provide some case details so we could help look into that further.
Once we support get updated information with firmware release or new beta, we will update on Page one of this thread, go the first page to check if there is any new firmware that you could give it try first, thank you.
- Copy Link
- Report Inappropriate Content
For TL-WPA4220 V4/V5, please go to Page one of this thread to check if there is any firmware for your model, thank you.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 2
Views: 49878
Replies: 200