@TP-Link 

I've submitted my system the logs using the method you've provided.

I have managed to (hopefully) fix the issue with incorrect Insight times, by manually clearing the history for both of the users.

Before I did so, the Insight was showing 9h and 10h of usage without any history attached to it (see below)

That was of 8:13am and without either of the associated devices being turned on for the previous 12+ hours. Both of the numbers (9 & 10) were (coincidentally?) identical to the Daily time limit for each of the users.

After I cleared the history the Insight numbers are shown correctly. I will check tomorrow to see if they reset properly in the morning.

I have checked the timezone in the web GUI and it shows correctly "Australia/Sydney"

As for the app itself - there's nothing in the Monthly Report and the app stops responding (Android shows: "Deco isn't responding" message after a moment).

hello @TP-Link 

My device always automatically switches from DECO on the right to DECO with weaker signal and farther left.

So I am very interested and need new features 1.Reboot Schedule.2.Signal Source.

But 1. This firmware CAN'T be downgraded to the previous version.  This makes me stay away!!!

I am worried that there will be problems that cannot be resolved after the upgrade

Do you have a solution??

Please help me ,thanks.

@TP-Link 

Are there any news about the release date of the beta 1.6.0 for the Deco M9 Plus V2?

@TP-Link 

I've updated my M5 (x5) to the new firmware last week.

Overall it works good, but I have noticed the following issues in my setup:

• Incorrect amount of usage time in Insigiths (Parental Controls) (comparing to the real usage) - it forced me to remove limits for both of my kids (as they were hitting them much earlier while using their computers the same way as before the upgrade)
  
  Below are screenshots showing the stats after about 1 hour of usage for 2 users (one device for each user). Both users turned their computers about 50 minutes BEFORE I took the screenshots, yet both of them show completely incorrect usage times.
  
  I've checked History page for both users and the earliest log entry is at 9:07 and 9:08 respectively - where is the 3.9h and 10.7h coming from?
  
  Guessing here, but perhaps it has something to do with my time zone (I'm in Sydney/Australia) and the Insight doesn't take the timezone offset into consideration.
  I have monitored the numbers for 30 minutes and they changed to 3.9 and 11.2 respetively. The first user had the computer off (thus it stayed at 3.9) while the other user had the computer on for all 30 minutes (thus it increased from 10.7 to 11.2)
   
• Historical insights are missing for all days aside from today/yesterday
• Might be a coincidence, but once a day I am experiencing network issues (some Deco's go offline) for about 2-4 minutes.I have checked the auto reboot and it is disabled. This has not been the issue before.
• Monthly report is missing (and hard-locking the app on Android (Samsung Galaxy S20))

Overall it works fine and I like the option to finally set up source of signal for Deco's (and the frequency).

Good job guys and gals :-)

@dangduters 

after 1 or 2 days, my device suddenly gone again from the client list. Please kindly help

@TP-Link 

Yes, 1*M5 and 2*M3W under my TP-Link ID.

TP-Link wrote

@Auu 

Hi, could you please send the Deco App log to me:

Go to Deco APP>Overview>three lines on the top>help>contact Us>suggestions and send us the APP log.

 

By the way, how many Deco do you have since I only see 1*M5 and 2*M3W under your TP-Link ID?

Thank you very much.

 

@TP-Link 

Please find attached 

Yes it's just started after i upgraded the firmware, and rebooted

Yesterday I tried to reboot all the Decos, and suddenly it's now appear on the client list again