Official Release Deco M5 1.7.8
Current Release
For Deco M5(V1/V2/V3/V3.2)
Deco M5_1.7.8 Build 20240719 for All versions
Modifications and Bug Fixes:
1. Improve the device stability.
2. Enhance the system security.
3. Fixed the bug of Deco network disconnection after adding satellite Deco.
Note: We recommend all users upgrade to this firmware version for important security updates.
---------------------------------------------------------------------------------------------------
History Release
For Deco M5(V1/V2/V3/V3.2)
Deco M5_1.7.6 Build 20240305 for EU version
Deco M5_1.7.4 Build 20231222 for other versions(like US/CA/AU, etc.)
Modifications and Bug Fixes:
1. Improved system stability.
2. Fixed several security vulnerabilities.
For Deco M5(V1/V2/V3/V3.2)
Deco M5_1.7.3_Build 20230906
New Features/Enhancements:
1. Optimized the auto-upgrade function.
2. Optimized the accuracy of the client list display.
3. Improved system stability.
4. Fixed the bug that port scanning errors recognized some IOT devices as risky devices.
5. Fixed the bug that parental control doesn't take effect.
For Deco M5(V1/V2/V3/V3.2)
Deco M5_1.7.1_Build 20230608
Modifications and Bug Fixes:
1. Added the static route function.
2. Added the ability to customize the MTU.
3. Added IoT network function.
4. Added auto upgrade function
5. Added ECO Mode (includes Power Mode, Wi-Fi Schedule, and LED Control) to save energy.
6. Optimized the MAC Clone function.
7. Fixed the bug of network abnormality under specific ISP.
For Deco M5(V1/V2/V3/V3.2)
Deco M5_1.6.5_Build 20230110
Modifications and Bug Fixes:
1. Fixed the issue that failed to set up Deco on Android 13 phones.
2. Fixed the issue that the online client displays zero incorrectly.
3. Optimized the Network Optimization feature.
For Deco M5(V1/V2/V3/V3.2)
Deco M5_1.6.1_20220818
- Apply to US/EU/JP/AU/CA/TW/ID/UK/SW/EU/B4 versions.
- 1.6.1 firmware will be gradually released to different areas and if currently it could not be detected on the Deco APP, you could wait for a while or a firmware upgrade via web UI is recommended.
Improvements:
1. Optimized the Monthly Reports.
2. Improved system reliability.
Bug fixed:
1. Fixed the bug that clients won't be able to obtain IP addresses randomly.
2. Fixed the bug that insight/time limit of parental control won't reset the next day.
3. Fixed the bug that No-IP DDNS doesn't take effect under PPPoE connection.
4. Fixed the bug that the client list randomly does not show any client or recognizes satellite Deco as a client.
For Deco M5(V1/V2/V3/V3.2)
New Features/Enhancement:
1. Added Reboot Schedule for every day/week under Deco App > More > Reboot Schedule.
2. Added support for customizing Satellite Deco signal source under Deco App > Internet > Select the Satellite Deco > Signal Source.
3. Added support for customizing clients connection preference under Deco App > CLIENTS > Select the client > Click the gear icon on the right-up corner > Connection Preference.
4. Added No-IP and DynDNS to the DDNS settings under Deco App > More > Advanced > DDNS
5. Added Smart DHCP on/off switch in Access Point mode under Deco App > More > Advanced > Smart DHCP
6. Added a prompt when the Ethernet link rate goes down to 100Mbps.
7. Added schedule and bandwidth limit to guest network under Deco App > More > Wi-Fi > Guest Network.
8. When configuring Deco for the first time, you can choose to establish an IPv6 connection directly.
Related Articles:
Frequently Asked Questions on Deco Firmware Update
Deco Monthly Recap- Check What's Currently Going on With Deco
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi, I have seen a similar setup:
Modem > M5 (Main) >--cable--CPE210(AP mode))))---WiFi bridge---(((CPE210 (client mode)>---cable--- M5 (Satellite)
Then satellite M5 is ok to create an Ethernet Backhaul.
So I think you might need a pair of CPE210s to build a wireless bridge in order to create the Ethernet Backhaul.
Thank you very much.
best regards.
- Copy Link
- Report Inappropriate Content
Good to know! I actually did purchase a pair of CPE210 for this project but I thought since the other building was only about 100 ft away max having two setup was overkill. Next time I'm at this location I'll bring the other one and try it out. Thanks!
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@CenterInYou why don't you connect a laptop to the satellite Deco ethernet port via FTP cable and run a speed test on the laptop/PC? Keep in mind that whatever you do, a satellite Deco will be limited by the connectivity to the main Deco since a speed test will pass through it. If you would like to test a satellite, promote the satellite to main and test it directly.
- Copy Link
- Report Inappropriate Content
@Parushev Yes this route would totally work but it is added a few extra steps epically if you plan to do more than just once.
Over the years I've found the that being able to run a speed test from the main Deco really useful when troubleshooting internet issues. I think this and people trying to find the best balance of speed and coverage while finding the placement for their satellite makes sense to add this feature.
- Copy Link
- Report Inappropriate Content
@TP-Link Could you explain more about:
1. Optimized loT control experience.
4. Optimized the WAN-LAN auto-sensing function.
What are "loT" and "WAN-LAN auto-sensing"?
First time I read these terms...
For "WAN-LAN auto-sensing" I supose it is the automatic detection of which ethernet port is the WAN?
EDIT: nice to see there are also other new features which are not part of the changelog, for example devices to be isolated from the network.
- Copy Link
- Report Inappropriate Content
No VPN server? I received confirmation on a support request that it is coming with 1.7 firmware...
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@TP-Link is 1.7 EU ok to flash for people in the US?
- Copy Link
- Report Inappropriate Content
Information
Helpful: 15
Views: 237979
Replies: 873
Voters 5
