Range Extenders Support OneMesh/EasyMesh in AP Mode
Hey everyone!
We got some feedback from our community users requesting for Range Extender to support OneMesh/EasyMesh when works as an Access Point.
Currently, OneMesh/EasyMesh is not supported when the extender is set to Access Point Mode. However it is planned to support EasyMesh over Ethernet Backhaul under Range Extender mode.
It will start with RE315_V1 and gradually be added to other EasyMesh-supported extenders.
RE315 Supports EasyMesh Over Ethernet Backhaul
Note:
1. An extender needs to support EasyMesh (over Wi-Fi) first, then supports EasyMesh over Ethernet Backhaul.
2. Ethernet Backhaul only works when both your main router and satellite extender support EasyMesh over Ethernet Backhaul.
Other Mesh Options:
Option 1: Deco mesh system supports Ethernet backhaul under both Wireless Router and Access Point modes.
Deco Ethernet Backhaul feature and Topology
Kindly note that the Deco system is different from TP-Link OneMesh >>> TP-Link OneMeshâ„¢ VS Deco Mesh: What's the Difference?
Option 2: OneMesh---Compatible Powerline devices if your house is under the same power circuit/under the same power meter
Some powerline products could build OneMesh through Ethernet & house Power line
Powerline units that supports OneMesh
How to configure OneMesh with seamless roaming (Powerline Extender)
Related Articles:
Several questions about the OneMeshâ„¢ and Mesh
How to build an Ethernet Backhaul using TP-Link EasyMesh Range Extenders
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Is this firmware available?
I have the re315 and archer c80 router and I would like to use onemesh instead of ap feature.
Thanks,
Scott
- Copy Link
- Report Inappropriate Content
Hi, the firmware for RE315 is available and please refer to RE315 Supports EasyMesh Over Ethernet Backhaul
Best regards.
- Copy Link
- Report Inappropriate Content
Thanks for your feedback, But New firmware in not available at Egypt site,
is it coming soon? or i should use the link you sent to download the new firmware?
- Copy Link
- Report Inappropriate Content
hey @david-tp I saw that AX80 now supports EasyMesh via Ethernet Backhaul - does that mean AX90 is coming soon?
- Copy Link
- Report Inappropriate Content
Hi, I see the EU and EG shared the same download link, and if you haven't detected it on the Tether APP, it is ok to download the firmware via my link.
As for AX90, it hasn't supported EasyMesh yet and I think it still needs a while.
Thank you very much and best regards.
- Copy Link
- Report Inappropriate Content
@Solla-topee I am using two archer AX10 routers in my home setup. One sits in the ground floor and another in the above floor. The concrete between these floors is too strong for a strong WiFi connection between these two routers and I am using Ethernet cable to connect these two routers. It would be great if onemesh over Ethernet is supported in Archer AX10.
- Copy Link
- Report Inappropriate Content
With the latest firmware on both, you should already be able to do this with EASYMESH - once the firmware is updated, you will see there is a EasyMesh menu item now, and no OneMesh anymore. Then you can follow this:
https://www.tp-link.com/us/support/faq/3731/
- Copy Link
- Report Inappropriate Content
OK, so I literally just tried to do what I told you to do in the previous post - and it FAILS!!!!!!
1. I picked up another AX10 router - flashed to latest firmware so it has Easy Mesh.
2. Connected via LAN and on my main AX10, added the new Mesh device. This FAILED, saying it should be plugged in closer to the other router - why??/ ( will become obvious just now...)
3. Plugged it in closer to the main router - actually connected the LAN cable directly between my two routers. This time, the "Add new device" worked.
4. Moved the router to the room that has little/no WiFi
5. For a moment, it looked like it was actually working - had strong WiFi signal, same MEsh as the Main router etc - but then...
The "Internet" light on the remote unit started turning orange.
Eventually it came back on green, BUT, now that remote unit is linked via WiFi and not via the LAN cable - back to square one.
TP-LINK - please get you $%^$^% together!
- Copy Link
- Report Inappropriate Content
Information
Helpful: 159
Views: 41530
Replies: 239
Voters 130
