Official Release Deco M9 Plus 1.6.4
Current Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.4_Build_20240718
Release Note:
1. Improve the device stability;
2. Enhance the system security
---------------------------------------------------------------------------------------------------
History Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.3_Build_20231225
Release Note:
1. Fix the potential security vulnerability and its related problem.
2. Improve system stability and security.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.2_Build_20230906
Release Note:
1.Fixed the bug that parental control doesn't take effect.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.1_Build 20230403
Release Note:
1. Added Reboot Schedule for every day/week under Deco App > More > Reboot Schedule.
2. Added support for customizing Satellite Deco Signal Source under Deco App > Internet > Select the Satellite Deco > Signal Source.
3. Added support for customizing clients Connection Preference under Deco App > CLIENTS > Select the client > Click the gear icon on the right-up corner > Connection Preference.
4. Added No-IP and DynDNS to the DDNS settings under Deco App > More > Advanced > DDNS.
5. Added Smart DHCP on/off switch in Access Point mode under Deco App > More > Advanced > Smart DHCP.
6. Added a prompt notification when the Ethernet link rate goes down to 100Mbps.
7. Added schedule and bandwidth limit to guest network under Deco App > More > Wi-Fi > Guest Network.
8. Fixed the bug that the built-in speedtest has low speed test results.
Notes:
1. This firmware downgrade could be done via firmware recovery-How to use firmware recovery.
2. Please update your Deco APP to the latest version for the new features.
3. If there are non-1.6.0 models in the Mesh network, you may miss some new features but this feature will be supported via firmware update in the future.
4. You may miss some new features when Deco is set to Access Point mode.
Related Articles:
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Any info if this update is still in development? Or is this beta version the "final"
After "upgrading" the home network from m5's to m9's it feels more of a downgrade since a lot of features are gone now.
- Copy Link
- Report Inappropriate Content
disableDHCPplz wrote
I started getting the 500mpbs "cap" right after installing 1.6.0 beta. Tried all the QoS 1000mbps stuff and no QoS. Only thing that fixed it was going back to 1.5.6.
@disableDHCPplz
My experience has been that the cap has been there since atleast 2020 which ever software was on it then as mine has never run at full speed, reset the units swapped them round etc nothing worked. If I use the ISP supplied router I get over 900mbps. Seems Tp-link have deeper problems. I've now lost automation settings on the decos since I updated the beta.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
how did you reverse back to ver1.5.6? mine is HW ver 1.1. Can I just use web browser and upload ver 1.5.1 to reverse back without using any recovery utiliy?
Thanks
- Copy Link
- Report Inappropriate Content
I started getting the 500mpbs "cap" right after installing 1.6.0 beta. Tried all the QoS 1000mbps stuff and no QoS. Only thing that fixed it was going back to 1.5.6.
- Copy Link
- Report Inappropriate Content
My DECO M9 plus v2.8 would only show a max of 500mbps download when speed testing through the app. Had to downgrade back to 1.5.6 for it to correctly get the speeds over ethernet again.
- Copy Link
- Report Inappropriate Content
Seems like tp link is giving up on everything
- Copy Link
- Report Inappropriate Content
@rekeen01 Tplink seems to have given up on this update
- Copy Link
- Report Inappropriate Content
This firmware update has been in beta testing for an entire half year. When will it be stable and available via the app? It can't possibly still be in testing, right?Thank you.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Information
Helpful: 8
Views: 142063
Replies: 436
Voters 2
