Official Release Deco M9 Plus 1.6.4
Current Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.4_Build_20240718
Release Note:
1. Improve the device stability;
2. Enhance the system security
---------------------------------------------------------------------------------------------------
History Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.3_Build_20231225
Release Note:
1. Fix the potential security vulnerability and its related problem.
2. Improve system stability and security.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.2_Build_20230906
Release Note:
1.Fixed the bug that parental control doesn't take effect.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.1_Build 20230403
Release Note:
1. Added Reboot Schedule for every day/week under Deco App > More > Reboot Schedule.
2. Added support for customizing Satellite Deco Signal Source under Deco App > Internet > Select the Satellite Deco > Signal Source.
3. Added support for customizing clients Connection Preference under Deco App > CLIENTS > Select the client > Click the gear icon on the right-up corner > Connection Preference.
4. Added No-IP and DynDNS to the DDNS settings under Deco App > More > Advanced > DDNS.
5. Added Smart DHCP on/off switch in Access Point mode under Deco App > More > Advanced > Smart DHCP.
6. Added a prompt notification when the Ethernet link rate goes down to 100Mbps.
7. Added schedule and bandwidth limit to guest network under Deco App > More > Wi-Fi > Guest Network.
8. Fixed the bug that the built-in speedtest has low speed test results.
Notes:
1. This firmware downgrade could be done via firmware recovery-How to use firmware recovery.
2. Please update your Deco APP to the latest version for the new features.
3. If there are non-1.6.0 models in the Mesh network, you may miss some new features but this feature will be supported via firmware update in the future.
4. You may miss some new features when Deco is set to Access Point mode.
Related Articles:
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Stick with 1.5.6 or, please stop using TP-LINK shizzle.
- Copy Link
- Report Inappropriate Content
@David-TP I still have the speed drop issue. Downgrading to the previous firmware is not possible. When will there be a solution?
- Copy Link
- Report Inappropriate Content
@MarvinZH I downgraded due to instability issues, link is one of the earlier pages, I'd recommend using a laptop as it can be easier to set up to reset all one by one
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@MarvinZH for me, all I had to do was downgrade and they reconnected, but the one I didn't have connected to ethernet did need a reset from the button, and needed to be readded to the network before it worked :o
- Copy Link
- Report Inappropriate Content
( 1. This firmware CAN'T be downgraded to the previous 1.5.6 version. )
Some people already downgraded the firmware to 1.5.6 due to abandoned beta program for M9+ and I wish to do this too, but how?
If it's an official method, why you guys put this note on the first place on the main thread?
- Copy Link
- Report Inappropriate Content
Can I have more details about your speed issue after the 1.6.0 upgrade?
How did you run the speed test? via Ethernet cable or wireless connection?
Please also help me check whether the speed dropped as well when only the main M9 plus is connected.
Wait for your reply.
Best regards.
- Copy Link
- Report Inappropriate Content
Hi, Deco M9 plus could be downgraded back to 1.5.6 from 1.6.0 via firmware recovery-How to use firmware recovery. It is not a common troubleshooting suggestion unless there is none left. Normally it is used when Deco was bricked.
Best regards.
- Copy Link
- Report Inappropriate Content
@David-TP Thanks for your comment. You're not going to believe it, but since the downgrade to 1.5.6, the speed is back to normal! The downgrade finally succeeded. I will never update to 1.6 again.
For all those with a speed drop, downgrade to 1.5.6 and the problem is fixed.
- Copy Link
- Report Inappropriate Content
@MarvinZH I wouldn't write off 1.6 entirely, just wouldn't advice the current beta. or almost any pre-release firmware from TP-link.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 10
Views: 109718
Replies: 440