Official Release Deco M9 Plus 1.6.4
Current Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.4_Build_20240718
Release Note:
1. Improve the device stability;
2. Enhance the system security
---------------------------------------------------------------------------------------------------
History Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.3_Build_20231225
Release Note:
1. Fix the potential security vulnerability and its related problem.
2. Improve system stability and security.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.2_Build_20230906
Release Note:
1.Fixed the bug that parental control doesn't take effect.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.1_Build 20230403
Release Note:
1. Added Reboot Schedule for every day/week under Deco App > More > Reboot Schedule.
2. Added support for customizing Satellite Deco Signal Source under Deco App > Internet > Select the Satellite Deco > Signal Source.
3. Added support for customizing clients Connection Preference under Deco App > CLIENTS > Select the client > Click the gear icon on the right-up corner > Connection Preference.
4. Added No-IP and DynDNS to the DDNS settings under Deco App > More > Advanced > DDNS.
5. Added Smart DHCP on/off switch in Access Point mode under Deco App > More > Advanced > Smart DHCP.
6. Added a prompt notification when the Ethernet link rate goes down to 100Mbps.
7. Added schedule and bandwidth limit to guest network under Deco App > More > Wi-Fi > Guest Network.
8. Fixed the bug that the built-in speedtest has low speed test results.
Notes:
1. This firmware downgrade could be done via firmware recovery-How to use firmware recovery.
2. Please update your Deco APP to the latest version for the new features.
3. If there are non-1.6.0 models in the Mesh network, you may miss some new features but this feature will be supported via firmware update in the future.
4. You may miss some new features when Deco is set to Access Point mode.
Related Articles:
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@HopSaSam still not released yet..
- Copy Link
- Report Inappropriate Content
Any update as to when 1.6 will be released officially? It's been two weeks. Are we looking at another month or so? Thanks.
- Copy Link
- Report Inappropriate Content
@rekeen01 probably Tp-link will release 1.6 version with all the bugs that this forum found.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
My main concern is the initial 500mbps from the service provider becomes 200mbps only after passing through the first deco then it further reduces down the series of access point.
Is this normal? How about other mesh brands? Do they reduce wifi also by that much?
I am open to recommendations which are a reliable mesh brands. Thank you.
- Copy Link
- Report Inappropriate Content
Hi,
I don't have your problem. I have my m9 plus wired.
I have a lot (60) of IOT devices, plus home server, phones, etc
Wi-Fi test
https://www.speedtest.net/my-result/a/9151539399
- Copy Link
- Report Inappropriate Content
Thanks for your response. For me, router to first deco unit is wired but the other two are wireless. But i see a big drop from the first unit.
I'll consider and think about wired set up if doable for me. Thanks.
- Copy Link
- Report Inappropriate Content
It is how the system works. For every hop, there will be a speed reduction of 50%. The back haul 5GHz channel (the second 5GHz) is supposed to mimic the wired back haul but I think the decos still use the other 2 channels (2.4GHz and 5GHz) for pulling data from the main deco. A wired Ethernet back haul will not produce this drop in speed.
- Copy Link
- Report Inappropriate Content
My first deco connect to managed switch.
I have 1000/200 from my ISP, my wired iMac gets 940/230 on speed test. It's everything ok, also nat/port forwarding.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 8
Views: 149454
Replies: 436
Voters 2
