Configuration Guide How to Build an Ethernet Backhaul Using Two EasyMesh Routers
Configuration Guide How to Build an Ethernet Backhaul Using Two EasyMesh Routers
Introduction
Building a robust and efficient EasyMesh network with Ethernet Backhaul is a great way to enhance your home Wi-Fi experience. In this article, we will guide you through the process of setting up an Ethernet Backhaul using two EasyMesh routers.
Please note that the Ethernet Backhaul only works when both your main router and satellite router support EasyMesh Ethernet backhaul. For TP-Link routers that already support Ethernet Backhaul, please refer to this thread: EasyMesh Routers Support Building a EasyMesh Network via Ethernet Backhaul NOW
If your router doesn't support it at this moment, please pay attention to the firmware release note if you receive any new firmware update for your router to confirm if Ethernet Backhaul is added or not.
Configuration Guide
Scenario 1: Change wireless backhaul to Ethernet backhaul
If both the main router and satellite router are already in an EasyMesh network via wireless backhaul, and the firmware that supports Ethernet backhaul has been installed, you could directly connect the main router’s LAN port to any Ethernet port of the satellite via an Ethernet cable to use Ethernet backhaul.
Scenario 2: Add a new satellite router to EasyMesh
At this point, please don’t configure the satellite and make sure it is under factory mode at first, if it was configured before, please reset the satellite router to factory defaults first.
Then connect your main router’s LAN port to the satellite’s LAN port via an Ethernet cable.
Tips
1. When adding a new router to EasyMesh, please use the satellite router’s LAN port as the backhaul port. After EasyMesh is built, all the ports on the satellite router (WAN, LAN, WAN/LAN) are available for Ethernet backhaul.
2. As long as the Ethernet backhaul is built successfully, the wireless backhaul will disconnect automatically. Similarly, if the Ethernet backhaul is disconnected for some reasons, devices will rebuild the mesh network via the wireless backhaul.
How to confirm whether Ethernet Backhaul is working or not?
Please login the web interface of the main router and go to EasyMesh page, you will be able to see the Connection of each satellite device, and Ethernet icon means it is connected via Ethernet Backhaul.
If it still shows wireless icon, please check if the Ethernet cable is functioning and connected correctly or not.
Related Articles
What is EasyMesh?
What is Wi-Fi EasyMesh and how does it work with TP-Link routers and extenders?
EasyMesh Routers Support Building a EasyMesh Network via Ethernet Backhaul NOW
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi, we don't have advanced notice about when Archer Air R5 will support it, please monitor new firmware update on the router web interface or TP-Link official website.
- Copy Link
- Report Inappropriate Content
@Sunshine Hello Sunshine,
Please allow me to ask a few more questions related to EasyMesh/Ethernet backhaul:
1) main router is the EasyMesh controller. When connecting satellite routers, can I connect them as a daisy chain configuration or do they need to be in star topology?
I ask because TP-Link describes the following: " There are three different components in a mesh WiFi network:
Controller: Every EasyMesh network must have one. All agents are connected to it (including through indirect connections). " - https://www.tp-link.com/en/blog/288/
keep in mind there are several users like me that want to have 1 main router and 3-7 satellite routers, all connected via Ethernet backhaul.
2) will this configuration work?
I have a main router setup as EasyMesh and being the controller (AX72 v1), from LAN port#1 I am connecting TP-Link switch TL-SG105, and from the switch I connect to 3 x AX53 V1 routers as satellite; AX72 LAN ports #2 through #4 connect to 3 x AX53 V1. Totaling 6 satellites. All connections via CAT6 cable for Ethernet backhaul.
Will EasyMesh be established? What is the controller's limit for maximum number of EasyMesh satellite routers?
Thank you, Eddie.
- Copy Link
- Report Inappropriate Content
Eddie_G_Kibel wrote
@Sunshine Hello Sunshine,
Please allow me to ask a few more questions related to EasyMesh/Ethernet backhaul:
1) main router is the EasyMesh controller. When connecting satellite routers, can I connect them as a daisy chain configuration or do they need to be in star topology?
I ask because TP-Link describes the following: " There are three different components in a mesh WiFi network:
Controller: Every EasyMesh network must have one. All agents are connected to it (including through indirect connections). " - https://www.tp-link.com/en/blog/288/
keep in mind there are several users like me that want to have 1 main router and 3-7 satellite routers, all connected via Ethernet backhaul.
2) will this configuration work?
I have a main router setup as EasyMesh and being the controller (AX72 v1), from LAN port#1 I am connecting TP-Link switch TL-SG105, and from the switch I connect to 3 x AX53 V1 routers as satellite; AX72 LAN ports #2 through #4 connect to 3 x AX53 V1. Totaling 6 satellites. All connections via CAT6 cable for Ethernet backhaul.
Will EasyMesh be established? What is the controller's limit for maximum number of EasyMesh satellite routers?
Thank you, Eddie.
Hi,
1. Daisy-chaining them can be effective especially when you have the option to connect the routers using Ethernet cables. If you have to use WiFi Backhaul, for optimal performance, it is recommended to limit the number of hops, which is no more than two hops, such as the main router )))((( satellite 1)))((( satellite 2.
2. For EasyMesh Ethernet backhaul or hybrid networks with both Ethernet and Wi-Fi backhaul, there is theoretically no limit to the number of units that can be added. However, we still recommend up to 6 units for better experience and performance. Considering your configuration with 7 units in total, it is worth a try. The topology you have set up is acceptable, but it's important to keep in mind that exceeding the recommended limit of 6 units may impact the overall performance and user experience.
By the way, AX53 V1 official firmware doesn't support Ethernet Backhaul yet, you could check the device list here and as you can see there is a beta firmware for AX53 V1: EasyMesh Routers Support Building a EasyMesh Network via Ethernet Backhaul NOW
- Copy Link
- Report Inappropriate Content
I have a question:
If I have a C80 as main router and I plan to add an ax53 as a Satelite router, will the extra (AX) features work on the ax53?
I'm wondering because after adding it in easy mesh, I won't be able to access the ax53's admin page to turn on those features and I don't know what is the status of these features after the recommended factory reset on it.
Why I want to choose the C80 as main router is because its location next to the ISP's modem is where there is no need for as many connected devices as the other location where I want to install the ax53 (for that exact purpose).
- Copy Link
- Report Inappropriate Content
@Sunshine Good afternoon Sunshine,
Hope all is well. I was waiting for Archer AX53 V2 to release the official firmware, as using the BETA version Archer_AX53_V1_1.2.4_Build_20240206 I found instability with EasyMesh Ethernet Backhaul.
Today I decided to run the upgrades, as the official firmware was released (Archer AX53(US)_V1_240509). Ran the EasyMesh setup as per TP-Link website. Once finished, these 2 Archer AX53 were wirelessly connected as ethernet backhaul.
My topology:
Archer AX72 V1 as main.
2 CAT6 network cables from Archer AX72 LANs 1 and 2 connecting directly to Archer AX53 LAN ports.
Once the CAT6 cables are connected, I continue to see in Archer AX72 that the Archers AX53 are wirelessly connected. Hence the ethernet backhaul is not in place!
Clearly is something broken in the firmware, either in AX72 or AX53. Please could you contact support and find out how can they troubleshoot and fix this bug?
Sincerely,
Eddie.
Sunshine wrote
Eddie_G_Kibel wrote
@Sunshine Hello Sunshine,
Please allow me to ask a few more questions related to EasyMesh/Ethernet backhaul:
1) main router is the EasyMesh controller. When connecting satellite routers, can I connect them as a daisy chain configuration or do they need to be in star topology?
I ask because TP-Link describes the following: " There are three different components in a mesh WiFi network:
Controller: Every EasyMesh network must have one. All agents are connected to it (including through indirect connections). " - https://www.tp-link.com/en/blog/288/
keep in mind there are several users like me that want to have 1 main router and 3-7 satellite routers, all connected via Ethernet backhaul.
2) will this configuration work?
I have a main router setup as EasyMesh and being the controller (AX72 v1), from LAN port#1 I am connecting TP-Link switch TL-SG105, and from the switch I connect to 3 x AX53 V1 routers as satellite; AX72 LAN ports #2 through #4 connect to 3 x AX53 V1. Totaling 6 satellites. All connections via CAT6 cable for Ethernet backhaul.
Will EasyMesh be established? What is the controller's limit for maximum number of EasyMesh satellite routers?
Thank you, Eddie.
Hi,
1. Daisy-chaining them can be effective especially when you have the option to connect the routers using Ethernet cables. If you have to use WiFi Backhaul, for optimal performance, it is recommended to limit the number of hops, which is no more than two hops, such as the main router )))((( satellite 1)))((( satellite 2.
2. For EasyMesh Ethernet backhaul or hybrid networks with both Ethernet and Wi-Fi backhaul, there is theoretically no limit to the number of units that can be added. However, we still recommend up to 6 units for better experience and performance. Considering your configuration with 7 units in total, it is worth a try. The topology you have set up is acceptable, but it's important to keep in mind that exceeding the recommended limit of 6 units may impact the overall performance and user experience.
By the way, AX53 V1 official firmware doesn't support Ethernet Backhaul yet, you could check the device list here and as you can see there is a beta firmware for AX53 V1: EasyMesh Routers Support Building a EasyMesh Network via Ethernet Backhaul NOW
- Copy Link
- Report Inappropriate Content
Information
Helpful: 9
Views: 12321
Replies: 15