Official Release Deco S7 1.5.0 Supports Connection Preference, IOT Network, WPA3 and More
This Article Applied to
Deco S7_V1/V1.2
Current Release
| Deco S7_V1/V1.2 | 1.5.0 Build 20240329 | ***The 1.7.0 Platform |
Firmware Modifications
1. Support for customizing signal sources of Satellite Decos and mobile clients.
2. Support for Reboot Schedule.
3. Support for NO-IP and DynDNS.
4. Support for WPA3.
5. Support for setting Effective Time and Bandwidth Limits for the Guest Network.
6. Support Device Isolation.
7. Added Smart DHCP switch under Access Point mode.
8. Added connection type of V6 Plus.
9. Added the Static Route Function.
10. Added the ability to customize the MTU.
11. Added IOT Network Function.
Notes!
1. The firmware downgrade needs to be implemented via firmware recovery and it can't be rolled to 1.4.5 directly via web UI.
2. Please make sure the Deco APP is up-to-date.
3. Some features might not be available when there are other models in the Mesh network.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi, Thanks for the update.
I have escalated your case to the senior engineer for further assistance.
Please check the email for more suggestions.
Best regards.
- Copy Link
- Report Inappropriate Content
Hi, the firmware downgrade from 1.5.1/1.5.0 to 1.4.1 needs to be implemented via firmware recovery-HTTP Uboot Method:
How to use firmware recovery on Deco
You could download the 1..4.5 bin file from the official website:
https://www.tp-link.com/en/support/download/deco-s7/#Firmware
Thank you very much and best regards.
- Copy Link
- Report Inappropriate Content
@David-TP If I update my deco S7 to beta version 1.5.0 when the official version is released, will I automatically receive the adjustments from it or will I need to manually update again? Can you help me with this?
- Copy Link
- Report Inappropriate Content
I would wait... I'm currently running a beta variant of 1.5.1 which seems to be ok so far..
If what you have works, leave it.
- Copy Link
- Report Inappropriate Content
Thank you very much for the update. 
Hi, you will receive the new official firmware notification via Deco APP even though you are on the beta firmware now.
Best regards.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
In case anyone is looking for the Download link of Deco S7 1.5.0 firmware to apply a manual firmware upgrade: https://static.tp-link.com/upload/firmware/2024/202405/20240529/S7_1.5.0_240329.zip
For some reason, this is not listed in Deco S7 download center firmware update list.
I needed to go with a manual firmware upgrade for 1 of my 4 Deco S7 devices. The 3-pack I originally bought were V1.2 devices which got the 1.5.0 update automatically. But the 1-pack I bought later as an addon was apparently V1.0 and this one refused to upgrade itself to 1.5.0, it showed 1.4.5 as the latest update available. This caused the whole network and all other Decos to also not offer the added functionality of 1.5.0 such as connection preference. Therefore, I have applied 1.5.0 upgrade manually on that specific Deco S7 and then all features were available once again. So far things are working OK.
- Copy Link
- Report Inappropriate Content
@David-TP Hello, good morning, I wanted to talk about the current firmware that you uploaded, what would be the version beta firmware Deco S7_V1/V1.2_1.5.1_build_20240711, It has a small problem and that is that my ISP assigns me an address that changes constantly throughout the days through PPPoE authentication, and when it does so the deco s7 detects that there is no internet connection although luckily the device continues to provide internet stably but the LED changes to a solid red color, and does not allow connecting to the deco outside the internal network, the following error is shown in the logs: [sntpc]wan No Link
- Copy Link
- Report Inappropriate Content
Hi, May I know your internet service provider?
Did your ISP support both IPV4 and IPV6?
Please refer to this link to change the WAN/IPv4 DNS to 8.8.8.8/8.8.4.4 to see whether it helped:
How to change DNS server settings on my Deco
Wait for your reply and best regards.
- Copy Link
- Report Inappropriate Content
@David-TP Hello, good evening, my ISP is Telefónica de Argentina, it only provides through the IPv4 protocol, I am currently using custom cloudflare DNS, even if I change them to Google's it would work normally again, but the error will appear again once I my provider changes my IPv4 address automatically.
This problem does not affect my internet browsing but it does present a problem and that is that the light on my deco turns solid red and also does not allow me to connect to the decos being outside my network.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 4
Views: 10681
Replies: 88
Voters 3
