How to Install and Configure the Deco X50-Outdoor

How to Install and Configure the Deco X50-Outdoor

How to Install and Configure the Deco X50-Outdoor
How to Install and Configure the Deco X50-Outdoor
2024-06-14 10:02:47 - last edited 2024-06-21 09:34:38
Model: Deco X50-Outdoor  
Hardware Version:
Firmware Version:

Note:  
1. Deco products cannot wirelessly link to non-Deco networks.
2. It is recommended to configure the Deco X50-outdoor inside near one of your Deco nodes first before mounting it.

 

If you prefer video instructions, please refer to Configuring and Mounting the Deco X50-Outdoor

                               

 

 

Here are step-by-step guide:

1. Power on Deco X50-Outdoor

1) Remove the base plate from Deco X50-Outdoor (store carefully to avoid losing base plate and screws).

2) Power on the Deco X50-Outdoor through method 1 or 2.

  • Method 1: through IEEE 802.3at PoE switch or IEEE 802.3at PoE adapter
  • Method 2: through 100-240V~50/60Hz 0.5A AC power supply.

    Note: Using AC power outdoors will require a weatherproof outlet to be used.

2. Configure Deco X50-Outdoor with the Deco App How to add an additional unit to your Deco network.
3. Select a suitable installation location

The Installation location can significantly impact performance and coverage range.

 

Here are some suggestions when choosing the right location:
1) Ensure a stable and secure power supply at the installation location.

  • If using PoE, consider the reach of the Ethernet cable.
  • If using AC power, check for nearby outdoor waterproof outlets that can provide power.


2) If X50-Outdoor and the closest indoor Deco are connected wirelessly, it is recommended to keep the distance between X50-Outdoor and indoor unit between 33 feet (or 10 meters) to 50 feet (or 15 meters). It is preferable to place the indoor Deco near a window, if possible, to minimize the obstacles between the two units. If X50-Outdoor and the indoor unit are connected via ethernet, then there is no such restriction.


3) It is recommended to install X50-Outdoor at the center of the target area where you want to expand the WiFi coverage to evenly cover the entire area.


4) The recommended installation height is between 0 and 25 feet ( 0 and 8 meters)


5) There should be a clear line of sight between X50-Outdoor and the area to be covered. Buildings, trees, or walls can weaken the signal strength and limit the coverage range.


6) Try to stay away from potential sources of WiFi interference, such as neighboring WiFi networks, high-voltage power lines, electronic devices, and appliances.


7) It is recommended to install X50-Outdoor in a location where it is more protected from rain and direct sunlight.

 

All installations will vary depending on the environment, so it's always a good idea to perform pre-and post-installation site surveys, measured to your desired data rates, as is the case when configuring any wireless extender or Access Point.

4. Mount X50-Outdoor 1)Please insert the Ethernet cable and/or power cord according to your own situation.
  • PoE-powered: Ethernet cable only
  • AC-powered: Wireless: Power cord only ;Wired: Ethernet cable + Power cord

2) Install the base plate back to waterproof X50-Outdoor.

 

Currently, we recommend two mounting methods:

  • Pole Mounting

1) Lead the end of the pole mounting strap through the back of the Deco.
image-20230929113130-1,20230929183131u
2) Position the Deco and wrap the pole mounting strap around the pole. Feed the end through the screw-block and tighten the strap until the Deco is secure.
image-20230929113130-2,20230929183131v

 

  • Wall Mounting

1) Place the mounting bracket in the right position. Mark two positions for the screw holes. Drill two 6 mm diameter holes for the screws at the marked positions.
image-20230929113130-3,20230929183131c
2) Insert the plastic wall anchors into the 6 mm diameter holes. Align the mounting bracket to the plastic wall anchors and drive the self-tapping screws into the anchors through the mounting bracket.
image-20230929113130-4,20230929183131n
3) Align the mounting tabs on the back of the Deco with the slot of the mounting bracket. Push and slide the Deco downward until it locks into place.
image-20230929113130-5,20230929183131t
Note: The Deco can only be used in an upright direction. Please do not mount Deco X50–Outdoor in an inverted or side-standing matter. Incorrect mounting may result in the device failing to maintain its waterproof status.

 

 

  0      
  0      
#1
Options